About 12 years ago, I bought my first Tek 475 scope. I only had a 2,245A at the time, and this unit upgraded my workbench's bandwidth to 240MHz. Not bad for a scope rated at 200MHz. In fact, the 475A was rated at 200MHz but one step less vertical sensitivity. So mine has the best of both models. It also had the DM44 on top. Unfortunately, the display on the meter had dopey segment issues.
I got a manual for the DM44 and traced the problem to the DMM 2 chipset. I used the 475 scope function to look at the digital lines and finally found one that was trying to go high but couldn't. It looked similar to a runt pulse. I checked leakage between the pin and VCC and GND. The VCC path was open. I did a visual inspection looking for anything unusual.
I didn't find any obvious faults so I pondered my next move. If it can't go high enough to drive its neighbor, then maybe I could help it a bit. I grabbed a 10K resistor and got the signal to go a little higher. I figured I was on the right track, so I wired in a pot and dialed it.
The seven segment displays lit up right away and gave me a reading. I unsoldered the pot and tacked in a fixed resistor of the same value as the pot (it was a 5.1K, if I remember correctly). The DM44 is still working to this day. I tried to find a replacement for the DMM chip, but it has long been obsolete. I went to work and described the situation to our engineering manager.
His response: "You did not fix the scope by adding a pull-up resistor. I gave up the debate right there. I had not been detailed enough in my description. He was thinking design flaw. The actual cause was an open upper totem pole output transistor, which is a part failure. I just changed the output from a class B to a class A linear stage. Thankfully, the timing on these early DMM chips is slow, so no worries on interface.
This entry was submitted by Steve Lindberg and edited by Rob Spiegel.
Steve Lindberg has loved electronics since he received his first Weller soldering gun when he was 12. He has 35 years of experience in test, debug, and design.
Tell us your experience in solving a knotty engineering problem. Send to Rob Spiegel for Sherlock Ohms.
Steve, I can see why you did not pursue the discussion with your manager. If you had fixed a design flaw in the scope it would have called into question all their other purchases. This might have been a problem when using the equipment to verify designs.
The management response to a problem solved and equipment now working is priceless basically stating that the way you did it did not solve the problem. That is a big pile of management.
I like the way you think! I have a pile of older equipment, most of it works, the rest is still "in progress".
This brought to mind a Sony amplifier I bought surplus 30 years ago. Until this year, I never had the thing work! Before I bought it, many others had tried and failed to get the felt channel to work. I know this because an aquantance of mine had tried repairing it when he was a tech at the university where I purchased it from.
Over the years, I would pull this out and see if I could get any life from it. The problem ended up being the bias diode that was secured to the heatsink. Although it tested fine with an ohm meter, everything pointed to this component. I ended up replacing this diode with a red led and a 1N4148, connected in series as I needed this potential drop to match the original diode, which has long since been discontinued. I am sure that the thermal characteristics of this arrangement do not match the original, but the amp sounds great, and matches the right channel when bench tested.
Some times ingenuity goes a long way, especially with vintage equipment!
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
4 
