HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Blogs
Sherlock Ohms

Grinding Out the Angular Deflection

NO RATINGS
Page 1 / 2 Next >
View Comments: Newest First|Oldest First|Threaded View
Page 1/2  >  >>
Tool_maker
User Rank
Platinum
Re: Compensating for angular deflection
Tool_maker   3/21/2012 12:52:36 PM
NO RATINGS
Jeff, I totally agree with you. A one time permanent fix as opposed to constant tweaking is always preferable. By the way tolerances are given for a reason. Once you have solved the problem to consistantly be, not only within tolerance, but exceeding by a factor of 4, any further messing around is a waste of time and money. Well done kyoshi.

Kyoshi
User Rank
Silver
Re: Compensating for angular deflection
Kyoshi   3/14/2012 10:48:21 AM
NO RATINGS
Thank you for the compliment.  It did work out as almost the ideal engineering solution, solving a long-standing product issue with no additional cost other than the initial programming of the Blohm grinder.  The sensor based approach would be a fascinating project to try for an order of magnitude improvement over current best practice for "standard" machine tools.

Jeff_A
User Rank
Silver
Compensating for angular deflection
Jeff_A   3/13/2012 1:08:27 PM
NO RATINGS
As a control engineer, I am fascinated by the measurement approaches suggested.  As a mechanical/project engineer, I am on the side that says if you can grind in the compensation on each part and you get what you want in terms of accuracy, you should.  Any kind of sensor can eventually fail, connections fail, and sensors always needs to communicate with the controller.  If you don't have those components in your design, you won't have the failure mode, you won't have to put them on the BOM, inventory or buy them.  I think this is a great solution.

Kyoshi
User Rank
Silver
Re: grinding out the angular deflection
Kyoshi   3/13/2012 11:34:52 AM
NO RATINGS
I appreciate your input.  With the wide range of sensor technology available today in conjunction with inexpensive computational power a self-correction machine tool could obtain incredible levels of accuracy.

sensor pro
User Rank
Gold
Re: grinding out the angular deflection
sensor pro   3/13/2012 10:53:45 AM
NO RATINGS
I see your point. Just wanted to be helpful.

I hope I was.

Regards.

Kyoshi
User Rank
Silver
Re: grinding out the angular deflection
Kyoshi   3/13/2012 7:55:36 AM
NO RATINGS
If you were using an angular sensor with a reference to the work surface you could make linear corrections to the position to compensate for the positioning error introduced by the angular motion of the structure.  The linear correction of 5 ppm per arc second would be dependant on the the distance from the linear measurement reference for the Y-axis.  Angular motions would still be introduced at the tool, possibly creating inaccuracy when large die sinking tools are used.

The machine in question is a relatively rigid structure, the angular deflections were extremely repeatable under a range of operation conditions.  Real time measurements would be more expensive (and less effective) than mechanically compensating for the underlying structural deflections.

sensor pro
User Rank
Gold
Re: grinding out the angular deflection
sensor pro   3/12/2012 4:38:39 PM
NO RATINGS
I agree with you, but inorder to make corrections and ajustments you need to make measurements. This is a real time sensor, so while you see what are the errors in position, you can make correction.

Kyoshi
User Rank
Silver
Re: grinding out the angular deflection
Kyoshi   3/12/2012 3:35:36 PM
NO RATINGS
The workpiece is attached to the table, the diesinking form tool is attached to the bottom of the Z-axis.  Angular errors, positioning errors, straightness and squareness errors will all produce unwanted deviations from "perfect" in the finished workpiece.  Improving the machine accuracy will improve the accuracy of the workpiece, measuring the errors will only tell you how much error you are introducing into the workpiece.

sensor pro
User Rank
Gold
Re: grinding out the angular deflection
sensor pro   3/12/2012 1:55:33 PM
NO RATINGS
If I understand it correctly, you have one reference surface and then the other that changes its orientation. You can use a unit called EZ-TILT-5000, that reads two sensors and can provide you with individual angular orientation of each sensor and also the differencial. This way you can always see the actual deviation of the required surface in reference to the standard.

Kyoshi
User Rank
Silver
Re: grinding out the angular deflection
Kyoshi   3/12/2012 1:09:08 PM
NO RATINGS
It looks like a great sensor, but I am not sure how you would compensate for the angular error in this example.  The angular machine deflection is referenced to the machine table, and a mechanical compensation is necessary to maintali Z-axis squareness to the machine table (and workpiece).

Page 1/2  >  >>
Partner Zone
More Blogs from Sherlock Ohms
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
Sherlock Ohms highlights stories told by engineers who have used their deductive reasoning and technical prowess to troubleshoot and solve the most perplexing engineering mysteries.
Design News Webinar Series
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
5/13/2014 10:00 a.m. California / 1:00 p.m. New York / 6:00 p.m. London
5/8/2014 11:00 a.m. California / 2:00 p.m. New York / 7:00 p.m. London
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jul 21 - 25, Design Products With Bluetooth Low Energy
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: August 12 - 14
Sponsored by igus
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service