The driver’s side window on my Saturn SL2 sedan stopped working one day while I was out and about. When I got home, I took off the inside skin of the door to see what was wrong. The regulator arm was just hanging in space near the track at the bottom of the glass. I found the plastic piece that the regulator arm uses to lift the window -- it was in two pieces at the bottom of the door. I called the Saturn parts department to see if they had the plastic part in stock.
I was told the part wasn't sold separately and that the complete regulator was priced at $115. I needed the window to function so I went to the dealership and picked up the complete regulator. I mentioned to the guy at the parts counter that Saturn should offer the plastic part for sale. He agreed and told me a lot of people ask about getting just that part. I was able to install the regulator fairly quickly, since the plastic outer door panel is easily removed by unscrewing about seven plastic screws from the inside side of the door. This allows easy access to both sides of the inner workings of the door.
Later, when the passenger side window failed for the same reason, I took that door apart and removed the regulator so I could take it with me to compare it to the new one I was going to buy. When I was picking up the new regulator, I mentioned to a new guy at the parts counter that they should offer the plastic piece alone. He said they do.
Apparently, it has become a standard part due to the high number of failures and resulting requests. It was in stock at $7. What a deal. The ball joint on the end of the regulator arm is permanently attached to the arm, so I snapped the plastic piece on the ball with a large set of channel locks. I bought two of the plastic parts while I was there, so I was ready when the third one failed a year later. Shortly after that, a plastic part in the sun roof failed. Since a replacement sun roof is $1,700 -- and of course the broken part was not available à la carte -- it was time for a new vehicle.
This entry was submitted by John Zambito and edited by Jennifer Campbell.
Tell us your experiences with Monkey-designed products. Send stories to Jennifer Campbell for Made by Monkeys.
I owned a VW Passat. The plastic window clips (the ones that actually hold the window to the track) kept breaking. After the second time I got online and did some research. As it turns out, this is a very common problem with this vehicle; an Audi part (made by VW) was virtually identical except made from metal. I bought these and they fit perfectly. Never had the problem again. Being a design engineer myself, it hurt my brain a bit on this one; if both autos were using the same part, buying twice as many (simplifying the obvious here) should bring the part to a cost point where a plastic one wouldn't be needed. Never underestimate the bean counters...
I had a similar issue issue with a 76 Datsun B210, the plastic had cracked vertically, fortunately the plastic piece was square so I removed the now two piece part rotated them 90 degress and reinstalled back in the sliding channel, as far as I know this lasted through my ownership and the two years my sister had it as well.
Zippi--excellent point. I do work with "additative" manufacturing and the choices for materials and processes expands each year. This technology is truly moving and moving quickly. There are still limits relative to component size but those are beginning to fall by the wayside also. You thoughts about minimal inventory are quickly coming to pass, which will be a boon for the automotive parts industry.
That's a really interesting insider perspective and not surprising, nyeng. I am sure that is a story repeated across many industries. Engineers do their job by thinking about what would work best and design products (cars, devices etc.) according to what would be the best material for the application. Then the number crunchers give them a budget and instructions for what materials are cost effective for the job. I am sure they often don't match up and you have to make do with what you can get! It must be frustrating sometimes.
I agree with Elizabeth. Plastic isn't necessarily 'bad' but it needs to be done properly. My personal opinion is that steel would be a better choice for that application giving the cyclical and shock loading as well as the temp extremes (windows are more difficult to move when the temp is below freezing).
As I've written before I worked as an engineer in the auto industry. It's all about cost. I didn't engineer parts to do the job at the lowest cost. Instead purchasing gave me a low cost part that fit their material cost reduction target and we had to engineer to work (as best we could).
Since you had to buy the window part it's obvious that the OE part lasted longer than 3 years or 36,000 miles. That's all GM cares about. In fact they don't want your car to last too long - they want you to buy another one. It's all short term thinking. I think the desire for fuel economy today might make this more of an issue. The desire for EPA number could drive more compromises in duraibility for the sake of light weight. About 3 years ago we were told GM would pay $1 per pound for weight reduction. Since we sold them a couple hundred thousand units per year it definitely got the bean counters' attention.
Plastic parts fail for the same reasons metal parts do: poor design, poor manufacturing, or improper use. Avoid these three things, and plastics (or metals) will perform just fine.
I view this from two sides. Since I make my living producing things from metal, mostly steel, I am somewhat amused when plastic parts fail. My industry lost thousands of parts, dollars and jobs to molded plastic parts so when they fail I can be smug about it.
On the other hand, I am a fisherman and have many reels with plastic gears that have never given me a moments grief, so I know properly engineered and manufactured, plastic can be a great substitute for metal. Some of the most expensive tackle is made from composites rather than aluminum, but I do not know if that qualfies as plastic.
A few years ago a plastic part broke in the mechanical timer of our old dishwasher. Took it apart and with my Dremel reworked the broken area and made it work again.
In spite of my technical repair skills, the wife was not pleased - what she really wanted was a new da*n dishwasher. A year later, when the top rack started falling off its rails and no parts available, I gave in.
Now the "new" (2 yrs old) diswasher is already losing broken plastic rack clamps.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
6 
