Made by Monkeys
Shim Fixed the Mower’s Metal-to-Metal Problem

Here's how the shim fixed the metal-to-metal problem.
Here's how the shim fixed the metal-to-metal problem.

Return to Article

View Comments: Oldest First|Newest First|Threaded View
Page 1/2  >  >>
User Rank
Not sure
naperlou   8/15/2012 9:00:01 AM
Ken, I have a similar mower (the auto trans version) and the same mulching cover, which we use.  I will have to check (I'm not home now), but I have not noticed any rusting or other problem.  If I do, I will comment later. 

Have you noticed rusting in the hole through whcih the clip goes?  This would be another area of contact?

User Rank
They don't want a better design...
kf2qd   8/15/2012 11:59:46 AM
Many of these products really seem to be designed so they will fail. And then you won't be able to get some part because they design was changed. They see it as a way to generate sales!

I have a couple of small machine tools at home and ther have been a number of time where I have made some simple part because the manufactirers part is either unavailable or way too expensive. If I can make it in 15 minutes why does it have to cost half te cost of the whole machine new? But then, most folks haven't the basic skills to open something up and repair it. Perhaps that is what we ought to be teaching in school nowadays. Then we might get better engineers and factory workers making better products.

Sorry to rip on the engineers, but they are involved in many of these "Made by Monkeys" complaints. How many of the engineers would be lost if handed a mechanics toolbox or a set of micrometers?

User Rank
Re: Not sure
KCB   8/15/2012 12:35:29 PM

It hasn't been very long that the clip's been in there.  I will be checking it

regularly however.  I would imagine that it will rust also.  I recently put

this same problem on a "Tractor" website and one responder said he's

been using the mulch cover without the clips to hold it in place.  He says

the metal deflector does a fine job of holding it in place.  I'm going to try

that and see what happens, because I can see that the same issue you

brought up will start to occur with the front clip as well.

User Rank
Re: They don't want a better design...
KCB   8/15/2012 12:44:45 PM

I think they call that "designed obsolescence."  On your

other comment regarding "design engineers," I've often

said, especially in regards to automobile engineers, that

they should be required to spend a year working in an

auto repair facility before they're allowed to work in a

designing capacity.  Nothing like a little hands-on, grease-

under-your-fingernails experience to let you know how the

real world works.

Rob Spiegel
User Rank
Re: They don't want a better design...
Rob Spiegel   8/15/2012 6:09:55 PM
Even simpler, Ken, those engineers should be required to go to online forums on their products. Every time I have a problem with a product, I go to the forums and sure enough, tons of others are having the same problem.

User Rank
Re: They don't want a better design...
Tim   8/15/2012 8:41:11 PM
I worked at a plastics company as a process engineer that required its design engineers to spend an entire shift running the assembly portion of all of their designs.  This forced them to design with ease of assembly in mind.  This procedure helped with the end quality of our product as it was easier for the operator to assemble.

User Rank
American made products
creamysbrianna   8/16/2012 8:24:29 AM
 As the author noted many Americans have come to accept sub-standard quality from American Corporations.  This really is a shame that so many people accept this sub-standard quality and do the right thing and buy better products that may not be made in America.  Myself I won't buy corporate crap anymore too many executives can not understand the "better" part of the "Faster", "cheaper", "Better" manufacturing mantra.

Personally I won't tolerate sub poor quality products and will only buy better quality products that meet my personal standards for quality.  I don't buy American just for the sake of buying American.  This is especially true with the fact that so many corporations have lowered their quality to the point of products being disposable today so that when the product fails it is more cost effective to buy a new one than to repair it.

Ok I will step down off my soap box now and let others get on it.

User Rank
Sending a letter ....
OLD_CURMUDGEON   8/16/2012 12:01:41 PM
"... sent a letter to the CEO of John Deere, including the attached picture, describing the issue and asking for their input. As of today, I'm still waiting for a reply. I guess the "monkeys" can't write... or design."

That's almost a joke in today's corporate culture!  CEOs of modern mega-production companies are too busy making deals to buy lesser companies in the global market to read a user's letter of complaint.  You just wasted a 44 cent stamp!  And, with this modern digital age, thinking that sending an e-mail is more efficient OR will elicit a quicker response, that's another joke!  That's why modern PCs have DELETE keys!!! 

I can't tell you how many times I've written (e-mailed) complaints to "Customer Service" departments for action, not from a personal-user point of view, but from a company point of view, only to get ZERO response!  It IS sickening to see the arrogance displayed by so many large corporations.  And, pathetically, there's just about nothing that one can do.  Because of their extensive legal departments, most of these large corporations have insulated themselves from any form of litigation, that it makes one totally powerless.  It's no wonder that the consumer is seeking alternate avenues of product to fill their wants.


User Rank
Perhaps the rubber connector is the problem?
econobiker   8/16/2012 1:43:29 PM
The John Deere instruction manual seems to show the rubber connector twisted 90degrees to the outboard from the mount point to the clip install.  The provided picture sppears to show the rubber connector stretched straight and flat against the cover or twisted only about 45degrees to the inboard side.

See instructions under: Using Mulch Cover (107 cm (42 in.) and 122 cm (48 in.)
Mower Decks (If Equipped) page 21

Possible link for manual: www.homedepot.com%2Fcatalog%2FpdfImages%2Ffd%2Ffd904936-46bd-471e-9536-7c3ca3698e81.pdf&ei=yyYtUISdBIesywHcrYH4Bg&usg=AFQjCNFlM-BnvKLa5EnYSpU9ZJBjR9n3RA&sig2=tllrFLeyxI2YFUMbuCdjOg


It also looks like the pictured connector is longer than the instruction manual version- possibly incorrect assembly of the connector to the plastic cover during manufacture or using the same length rubber connector for both front and side clips when the side is supposed to be shorter?

Also note that some consumers who reviewed the cover said that the rubber connector(s) were difficult to stretch onto the mount points:


That said I commiserate with you about the issue of the design allowing the clip to vibrate against the deck.  But the safety requirement for the design probably requires a complete and positive attachment of the cover to the deck - which used to be accomplished by bolting a cover like this onto the deck- but now seems to be accomplished by the hardened steel clips running through the deck.  

The consumers probably requested the ability to install and take off the cover without tools- in fact, one reviewer on the Lowe's website mentions this function. Most consumers today do not have tools available or want the convenience of removing the cover without tools.

The majority of consumers using this type of product probably do not have as much as a discriminating eye for rust issues, would discard the mower prior to the clip and rust perforating the cover steel, or just don't care about it as they would chalk the clip creating rust up to "in use wear" (much the same as the wear on the face of a hammer head).


Some other possible solutions if installation is verified as correct and the clip still rubs:

Wood shim (as you have done)

Rubber shim

Rubber cover wrapped around clip and zip tied to it/ into it

Dip the clip in rubber tool handle coating

Spray the in contact portion of metal cover with truck bed liner material






William K.
User Rank
Mowers metal-to-metal problem.
William K.   8/16/2012 10:11:18 PM
The comment about safety is right on. It is far more important to make a product safe than to have it be servicable or usable or durable. For this very sad fact we can thank the greedy lawyers and the incredibly stupid juries who handed out awards to people acting like idiots bent on self destruction. 

Doesn't anybody accept that some products and processes are intrinsicly hazardous? One of the better examples is the engine powered rotary mower. Not content with adding a whole lot of guarding, now these mowers have not only a dead-man type kill switch, but also a brake that puts a great deal of stress on all of the blade driving system. And a stupid arrangement that puts the rope starter in a difficult to use position.

A large improvement would be to revise the laws and have a waiver for all buyers to sign, stating that they alone are responsible for their safety. After all, "Onjly YOU can prevent stupidity". (Sorry, Smokey the Bear).

Page 1/2  >  >>
Partner Zone
More Blogs from Made by Monkeys
Made By Monkeys highlights products that somehow slipped by the QC cops.
Made By Monkeys highlights products that somehow slipped by the QC cops.
Made By Monkeys highlights products that somehow slipped by the QC cops.
Made By Monkeys highlights products that somehow slipped by the QC cops.
Made by Monkeys highlights products that somehow slipped by the QC cops.
Design News Webinar Series
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
12/10/2014 8:00 a.m. California / 11:00 a.m. New York
3/31/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Mar 30 - Apr3, Getting Hands-On with Cypress’ PSoC
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  67

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service