One day while I was doing laundry, my washer stopped in the middle of a cycle and the screen displayed the error code E20. Since the owner’s manual did not have any information on error codes, I went online to find an answer. Sure enough there it was -- error code E20 indicated that the “coin trap” was blocked.
I thought, “Wow, what a clever component -- a trap to block coins and other debris from ruining the evacuation pump.” So I looked for an access door only to find that it was on the rear of the machine. I moved the units away from the wall -- I have the washer and dryer stacked -- and proceeded to remove the back cover. There it was, the coin trap... behind three hoses.
The three hoses are connected to a boot at three different locations with three different kinds of clamps. This assembly is at arm's length, and there is only room for one arm to get in to work on it. After two hours, I managed to get two of the three hoses unhooked. I then looked for a solution to remove the last hose. I saw there was a cutout on the bottom of the washer, so I lifted the dryer off, tilted the washer back against the wall, and tried from the bottom.
After another hour I got the coin catcher assembly removed and cleaned out. Now I had to try to reassemble the boot assembly with one hand, blindly. When your hand is in the access area, you can't see in to line up the hoses and install the clamps. After five more hours of trying to remove the front panel and other options, I was ready to drag the machine down my driveway with a chain and put it out on the curb.
Then I thought, “I have nothing to lose. Why not make an access hole in the side?” So I got out my saber saw and cut a 12x12-inch panel in the side. In 10 minutes I had the boot and pump assembly together and the machine running again.
This entry was submitted by Gary D. Rodichok and edited by Rob Spiegel.
Tell us your experiences with Monkey-designed products. Send stories to Rob Spiegel for Made by Monkeys.
Thanks, this story gave me a good laugh. Especially when the author decided to make an access hole with his saber saw. I agree with Glenn. And why the heck not? If my husband wants to cut an access hole in the washing machine so he can spend less time messing with it and more with me, I'd be a happy camper. Actually, I'm more likely to be the one that comes up with that idea, since stubborn machines and bad designs annoy me more.
Use a phone camera of digital camera to take photos as you disassemble. Then you have a record of what goes where. I use my phone camera to make a visual shopping list before I go to Lowe's and Home Depot.
Well, maybe the coin trap was designed for ease of assembly, not for ease of servicing. That reminds me of cars where the engine must be dropped to change a spark plug. I like your decision to 'add' an access panel; maybe you will have to service the coin trap again ? Can you patent the modification and sell it to the manufacturer ?
there's is no way my wife would let me cut a hole in her washing machine! I've had the same problem with the coin catcher collecting guitar picks and coins. Since the debris belongs to me, I have to open the machine and get the junk out.
The negative reinforcement has worked in bringing the behavior to extinction. Dr. Skinner would be proud.
You would think they'd make a coin trap that was more accessible, somewhere where the non-fix-it could get access and empty it much like the lint trap. As the resident laundry person in my household, I can't tell you how many coins I collect (dollars too). My rule is the person doing the wash gets to keep the goods. I've found myself with a decent amount of play money over the years, which is why I don't whine too much about doing laundry!
Gardy nice experience and funny solution. Once I have a similar experience, while repairing a machine. I disassembled everything, rectified the problem and repaired. Still that time everything was under my control and done well. When I started reassembling, the confusion starts. Finally I found that some parts are screws are left over and I don't know where to be placed. Without that I switched on the machine and it works fine for some time. But later on found that some extra wear & tear, additional noises etc while operating the machine.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
0 
