One day I noticed that the front of my side-by-side GE refrigerator -- the space between the fridge and freezer -- was fairly hot to the touch. At first, I just blew it off, thinking the freezer was going through a defrost cycle. It also seemed the fridge was running constantly, but I still didn't think to investigate.
Then one day I went to get something to eat out of the fridge, and I stepped in a puddle of water. I wiped it up, assuming one of the kids carelessly spilled water or ice. But the next time I went to the fridge, it happened again.
Then my wife tried to get a glass of water (from the in-door dispenser) and failed. She said that it sounded like the water was flowing, but the glass didn't fill up.
Thus, the detailed investigation began. I pulled out the fridge and removed the back cardboard cover. Right away, I noticed the cooling fan was not running. So I ordered a new $30 fan.
I also found the source of the spilled water. With the fan not blowing to cool the coils, the coils never really got cool, and the coils between the fridge and freezer made the front hot to the touch. The coils not getting cooled caused the fridge to run inefficiently. They were basically running all the time. The water line was resting on the coils, and with the compressor running all the time, the water line melted through.
When there was a demand for water through the door or the ice maker tried to make ice, the solenoid valve opened and released water on to the floor. I spliced a connector into the water line to make sure it did not contact the coils. I replaced the fan, and we were back in business.
A couple months later, the problem started again, so I investigated right away. I discovered that the fan was broken again. I decided to take a different approach. I bought an office desk fan, clipped it the back of the fridge, and now I leave it on full time. The fridge has been running great with the desk fan for a couple of years now.
This entry was submitted by Bill De Vries and edited by Rob Spiegel.
Tell us your experiences with Monkey-designed products. Send stories to Rob Spiegel for Made by Monkeys.
Wife continually tells me that if I touch that, I will certainly have my fingers burned off. Frequently find I have to cool down after she visits. Turn on a fan or take a cold shower.
I will admit, my eyes do burn from staring so hard...so must be something to it.
I'm not so sure appliance designers are diabolical enough for planned obsolescence. Besides, disgruntled employees would eventually spill the beans if it were really a conspiracy to build products that break down. I think it's poor (in a hurry) craftsmanship mixed with pressure to build inexpensively.
Thanks - I'll have to look for the defrost timer. What would cause the fan motors to burn out other than cheap fan motors?
The deer is only short term seasonal until I can finish processing into vacuum seal bags and the deer can then find its way into the freezer for later consumption.
I might have to take up home brewing. I've been into craft IPA's lately.
Less Deer - More Beer - that hole in the front can be used to put a very natural looking tapper, direct from the pony keg within! One of my college room-mates very first projects, as soon as he was in his own home, (post graduation).
Double check your defrost timer. It is the number one failure mechanism. It is a mechanical rotary timer that shuts off the compressor and turns on the heaters to defrost. It gets dirty and stops turning after several years. Yours may have stopped in the "compressor on" cycle. This will run the compressor too much, causing frost build up. As the frost builds up, the compressor will have to run more to get the fridge cold. I could picture this continuing to the point where the compressor is overheating, breaking the icemaker tube etc.
Look behind the lower grill, or sometimes it is inside the fridge. It is a small knob. You should hear the compressor turn on and off, also the heaters will crackle when it is in defrost mode. Usually, just turning it a few times will loosen it up for the next few years.
I also replaced my fridge a few years back, with an Energy Star design. A model with the same basic footprint and interior size costs about half the electricity to run as the old one did by the even more inefficient end of its not-very-efficient life.
By the way - I LIKE "duct tape band-aide" approaches to solving things like this. Which is the reason for occasionally having the title of "cobblemiester"...
Sound like a good solution - although a bit of a "duct-tape band aide" approach. I probably would have gone on line to some place like surpluscenter.com and searched for a fan that I could cram into the spot.
Yeah planned obsolescence has got to be what it is. My "good" kitchen fridges have not lasted very long- 4th one in about 20 years. My garage "beer & deer" fridge is about 20 years old and still works fine as long as you know where to put different foods. Top shelf left side will freeze - don't put lettuce there, frosty beer on a hot summer day is quite nice. Anyway, the garage fridge holds the kitchen fridge overflow just fine. The ice maker in the garage fridge died, so I just removed it, insulated the hole in the door, and covered the hole with a plastic storage box lid - it almost looks like it was meant to be that way.
Yeah planned obsolescence has got to be what it is. My "good" kitchen fridges have not lasted very long- 4th one in about 20 years. My garage "beer & deer" fridge is about 20 years old and still works fine as long as you know where to put different foods. Top shelf left side will freeze - don't put lettuce there, frosty beer on a hot summer day is quite nice. Anyway, the garage fridge holds the kitchen fridge overflow just fine. The ice maker in the garage fridge died, so I just removed it, insulated the hole in the door, and covered the hole with a plastic storage box lid - it almost looks like it was meant to be that way.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
7 
