Back in the good old days when you could do these things, I yanked a broken six-cylinder motor out of my '53 Studebaker and dropped in a nifty Chevy 283 V8. I generally drove home from Troy, N.Y. to Boston well after dark to keep the car's various illegalities from the prying eyes of police. One particular evening, on a long uphill section of Route 2, the motor started screaming.
I pulled into a gas station and discovered after some disassembly that the generator had seized. I needed a new rear plate of the generator with its sleeve bearing.
The helpful gas station attendant told me where I could find the nearest Chevy dealer. He pointed in the direction of a small town at the bottom of the hill and said there should be a salesman hanging around to capture the last customer.
Then I asked him the key question: "Is it downhill all the way?"
He thought it over carefully and said it was, so I threw the parts in the trunk and pushed off. A few minutes later, with no additional pushing, I found the salesman and convinced him to sell me a new rear plate of the generator with its sleeve bearing.
And to my amusement, the new part differed from the old part in one important respect: the oil reservoir was much, much larger.
This entry was submitted by Larry Baxter and edited by Rob Spiegel
Tell us your experiences with Monkey-designed products. Send examples to Rob Spiegel for Made by Monkeys.
I had a similar experience. I bought a new 1969 Chevrolet Impala. After about 12,000 miles, the water pump front bearing sprung a leak that emptied the radiator in about 15 minutes. With a couple of refils, I managed to limt to the dealer. I hung around the shop to witness the repairs. When the mechanic had extracted the defective pump, he threw it into a corner. I look to see what else was there - it was a huge pile of several hundred identical water pumps!. I drove the car to 125,000 miles with no further problems with the water pump.
I had a 1985 Dodge van with that great 318 engine, and after about a year and a half I started to have starter motor problems, that gave similar symptoms to a dead battery. Friends all claimed a starter replacement was in order, while the dealer said that they could do it in only one day for "only"$175, and no, the starter is an engine accessory and not covered by the warranty. Instaed I went to the parts department and paid around $5 for a replacement sleeve bearing. I got back home, and found that pulling the starter, replacing the sleeve bearing, reassembling and re-installing the starter took me less than an hour in the driveway. Fortunately on the almost new van, none of the important bolts had rusted tight yet. The original bearing had failed before 5000 miles, the replacement was still working in 2006 when I got rid of the van because the front frame had rusted away, making it unsafe.
It would seem that there has been a serious quality problem with those starter motor bearings, as I had an identical failure in another Dodge.
Now that SSSSS and other "modern" people management processes have been implemented more widely, I would be amazed if those jigs and fixtures are still in existence since we're only supposed to keep that which is current product and everything we keep must have a place and be kept there. In other words, things without a current role have no place, ergo must be disposed of. More likely they have been re-purposed into raw steel for the growing Chinese middle class (now that we've decided we don't need ours anymore). Black & Decker was an early fan of this methodology; try and get a replacement part for any of their gear that isn't within 6 months of being current production.
Why is it a surprise that a reputable organization would sell repair parts for the products that they sell? All decent and reputable companies do that, and in addition, some reputable software companies do it. Others declare a product obsolete and refuse to support previous versions of product, so that repairs are not easy to do, or may be impossible to do because replacement parts are not available.
If this sounds like a criticism of some large companies, it is intended to be a criticism of those companies.
Many other companies make products worth repairing.
Replacement parts for old cars can be tough. I was in a Ford plant in southern Indiana once looking at some new production equipment for a current model. I noticed there was a huge warehouse area we weren't visiting. At my request we took a detour and it was a massive warehouse where Ford kept jigs and fixtures to make thousands of parts for cars no longer in production.
And to my amusement, the new part differed from the old part in one important respect: the oil reservoir was much, much larger.
It isn't always funny when the salesmen, or manufacturer, drops the latest surprise on you that the replacement parts are not 100% compatible.
The question there is, was this a marketing ploy, or a manufacturing oops.
It was a good thing that you had a downhill only trip however. I remember having to take the long-stride approach when one of my vehicles broke down to get a new distributor cap. Needless to say I had a good 20 mile trek that day.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
3 
