"If you decide you want to brake, and the engine is at wide-open throttle, the ECU tells the engine, 'No, we don't want to go fast; we want to stop,' " David Cole, chairman emeritus of the Center for Automotive Research, told us. "And the vehicle stops."
Since an overwhelming percentage of new vehicles already employ electronic throttle control, the technology would be easy for automakers to add at minimal cost. Toyota reportedly began incorporating BTO to its vehicles in 2010 by adding new software code as a running change.
"From what we've seen, it's very simple," David Champion, senior director of Consumer Reports' Auto Test Division, said. "We don't know of any new car that doesn't have an electronic throttle. We haven't seen one of the old throttle cables in a long time." The BTO fix would solve problems caused by sticky accelerators or trapped floormats, but it would be unable to address the issue of a driver who mistakenly depresses the accelerator instead of the brake. Drivers must hit the brake pedal to make it work, experts said.
Not everyone is happy with the idea. Race drivers, who occasionally hit the brake and gas pedals simultaneously, foresee a problem. What's more, some industry analysts see the mandate as yet another form of inappropriate government intervention.
Still, analysts said that automakers are likely to accept the mandate, not only because it prevents unintended acceleration, but because it provides a layer of legal protection for the industry. "It makes sense all around," Champion said. "We can't find a downside to it."
Related posts:
If you've always dreamed of hanging with the pit crew at Indy, your opportunity has arrived. Littelfuse Inc., a KV Racing sponsor, is sponsoring the Speed2Design contest. Winners will attend the race, visit the pits, and talk engineer-to-engineer with crew members.
Click on the link to access the entry form for the
Speed2Design contest.
In the old days of a cable linkage between the accelerator pedal and the carburetor, my brother had the experience of the return spring breaking. He turned off the ignition and the car stopped. Another option is to put the gear selector in Neutral. If you are truly concerned that the car won't stop, I don't think you will be worried that the engine will overspeed and throw a connecting rod. But then that would stop the engine. I do agree with having an interlock between the brake pedal and the electronic throttle control, but technology can't replace good driving skills.
It seems somewhat unfair that Toyota's acceleration problem got so much press when it was first examined, but when the cause was not found to be a software or electrical issue the media was mute. If the driver doesn't panic there are plenty of methods to disengage power by shifting into neutral or turning the car off. Adding this additional method to cut power in drive by wire systems wouldn't add any additional hardware, and would remove power even if the driver panics.
Yes but..good driving skills may include keeping the brake pedal depressed while giving the vehicle some gas when starting up on a steep hill so it won't roll backwards. Thus, the interlock firmware needs to be intelligent and not override the throttle the instant both both pedals are activated.
bdcst; Some vehicles have 'hill start assist' that maintains braking for a short time to allow time to press the accelerator. Rolling backward was more of an issue when the clutch pedal was also present. Some drivers have the (bad habit) of 'two-foot' driving; one foot on the accelerator and one foot on the brake; poor mileage, poor acceleration, brake pads wear out quickly, the driver following can't tell riding the brake pedal from actual braking.
From what Chuck describes, it also sounds pretty painless for the automotive makers to incorporate so why wouldn't they. As someone else pointed out, it could also provide some legal protection.
I wish to express my outrage at the lies contained in this report!
In its investigation NASA found examples of throttle sensors that had grown Tin wiskers that shorted out the pot's leads effectively indicating a full throttle command. The web link to the NASA paper is here: http://nepp.nasa.gov/whisker/reference/tech_papers/2011-NASA-GSFC-whisker-failure-app-sensor.pdf
This is an example of an undesirable side effect typical of every human endeavor. In this case the desire to eliminate lead from solder has resulted in a proliferation of tin wiskers causing no end of trouble in electronic circuitry.
I would question the use of carbon potentiometers for this critical throttle control application. D.C. voltage applied to a carbon pot makes it go noisy rather quickly . I'm not aware of a single carbon volume control pot, which by the way is normally only subject to A.C., that I've owned that hasn't got noisy within 10 years of use. We're talking about blow your speakers type noisy.
In one report on the Audi runaway problem, the engineer was able to readily reproduce the runaway problem caused by alternator noise wreaking havoc with the controller CPU when the battery's impedance rose at high temperature extremes.
It's obvious to me that both of your mentioned reports were written by the industry friendly mandarins of NHTSA and NASA. These do a major disservice to the hard work of some honest engineers, who take due diligence seriously, especially when people's lives are at risk.
Lighten up, "cookiejar." Your indignation about this matter is very selective. On one hand you refer to the "industry friendly mandarins of NHTSA and NASA." On the other, you cite a NASA pdf file to make your point about tin whiskers. The fact is, NHTSA's final report cited tin whiskers on pages 46, 48, 69 and 74 (those are the pdf page numbers), proving that it was aware of the issue. In the end, though, the report concluded that the tin whisker effect is not dangerous. Its conclusion was that it would have been impossible for tin whiskers to cause the Toyota vehicles to accelerate out of control. As I noted in the story, the Secretary of Transportation emphatically stated that the verdict was in: "There's no electronic-based cause for unintended high-speed acceleration in Toyotas. Period," he said. For this story, we also talked to the Center for Automotive Research and Consumer Reports. Reports by the National Academy of Sciences and by Edmunds.com have reached similar conclusions. If you can demonstrate that tin whiskers were the cause, I strongly suggest you call Edmunds, which offered a prize of $1 million to anyone who could demonstrate "a novel cause for unintended acceleration." If all these people are in on some kind of conspiracy, it must be a whopper.
To see NHTSA's final report, go to the following page and click on the link that says "NHTSA Full Report":
I agree with you, tekochip. Although there was a fair amount of media coverage when the Secretary of Transportation made his pronouncement, it paled by comparison to the amount of coverage the story got when it orginally broke.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
8 
