Nissan's next-generation steering employs a steering angle sensor at the steering wheel, three ECUs for control, electric motors to power the rack, and a steering force actuator near the driver to retain the vehicle's "steering feel."
So let me get this straight, we introduce steer by wire so we can remove the feel of rough roads etc. but we dial in the feel electronically because that wouldn't be good for the driver, and were saving weight even though we added 3 ECU's AND a clutch to re-engage the traditional steering column if all 3 ECU's die (which will happen every time an alternator dies)
I think some engineers in the automotive industry have lost the plot, They're putting complexity in for the sake of it.
I don't get it. All I see is a riduculously complex and expensive system which the owner has to pay for but adds little or nothing useful to the operation of the vehicle.
In my view, you had redundancy and tactile feedback with a rod that connects to the gear that moves the wheels. How much more elegant, cost effective and reliable can you get than that? Seems the weight issue is a materials question, not motors and redundant computers.
That is 100% correct. In the aerospace industry there is a massive effort to test and qualify all fly by wire systems to prove that they are fully redundent and fail safe. To incorporate this into a car without a mechanical backup will cause a very complex and expesive system. This is why the aircraft that are relatively inexpesive (single engine puddle jumpers) are still cable and pulley. We may see a day when drive by wire is 100% but I beleive it will be in the high end cars where cost is less of an issue.
I'm going to play teh antagonist here. When it comes to driving, feeling the road is much more important to me than a smooth ride. The feel actually helps me know that a tire has a problem before it is a real problem. I get the whole technology thing for the future, but nothing can replace a solid mechanical system. Removing that is like putting a rocket on the road with no breaks. There always seems to be delay in control system response, and that nanosecond of steering response has saved my life. I embrace technology, but I'm not confident that this is the right way to go.
Anyone remember the accelerating Toyotas? I know GM has been working on this for over 20 years. I think it will ultimately come down to consumers and federal mandates (such as CAFE).
The new 787 Dreamliner is entirely electronic. The difference is the rundundant back-ups are not going to exist in the physical sense on cars (weight, weight, weight). So the development in the automobile has to be sensor/control failsafe that stops the vehicle. It is better to get out of the car that is on the side of the road than trying to parachute out of an airplane with type of failsafe!
Today I drive a car with mechanical linkage and electric power boost (by chance, also a Nissan). Nissan propose to give me the same, with an extra sensor and wire to the steering mechanism. The electrical signal will be the primary mechanism, but so what? It doesn't replace the existing linkage. Its extra - extra weight, extra power, extra complexity. What happened to "keep it simple" ? Keeping the mechanical linkage in place as a backup is Nissans' way of saying "we like the new system - but we don't fully trust it"
I think the only down side is the number of automobiles on the road. The chances of the system failing are far greater than with cars. You cannot guarantee that the car is professionally maintained. However, if this system is fool proof, I mean that with masses in mind, then it is the future.
Right, Rob. For now, the clutch is there, but Nissan told us that if the mechanicals were ever removed, its engineers would incorporate a fail-safe sub-system. At this point however, it's not clear how the fail-safe sub-system would work.
Interesting story, Chuck. It seems that the real gain will come when the redundant mechanical steering is eliminated. Yet that means that you wouldn't have steering if the electrical system failed.
You're not alone, Greg. I think most consumers will feel safer knowing the shaft is there, at least until steer-by-wire has a few years of success behind it.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 4
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
25 
