1959 Taylor-Dunn Trident. Decades after the electric buggy and decades before the GM EV1, Taylor-Dunn produced the tiny, three-wheeled Trident between 1959 and 1963. The all-electric Trident was described as a "neighborhood cart" that could hit a top speed of 16 mph.
"On a motorcycle there is not much to do when some fool makes a left turn 30 feet ahead of you. Quickly laying the bike down and getting off doesn't make much difference at 45MPH, much less at 60. 20MPH it may reduce the damages."
@William- "Laying the bike down" is the wrong action if a crash is imminent. At that point the crash has started prematurely, there is no control of the direction and speed of rider and bike, the impact will usually be at a higher speed since sliding friction force is lower than braking force, you're more likely to go under a vehicle instead of over the top, and since the rider usually separates from the bike the small amount of impact absorption provided by the bike is not there. Rider safety courses and articles emphasize maximum effort braking to scrub off impact speed and energy. The one exception I can recall where "laying down the bike" is recommended is if you're going to go over a bridge rail or guardrail with a big drop on the other side.
OK, now add to your relevant facts that I was raised in a suburb of Detroit in the 1960s and its pretty clear why I never saw these models! Where I grew up everyone had either a Chrysler, Ford, GM or AMC vehicle; except the occasional VW, and very rarely, an aging Rambler. I never even saw a Mercedes until I moved away from home as an adult! No wonder these are "foreign" (literally) to me.
While the featured cars are all very interesting, where are the Asian microcars? Wikipedia lists several by Cony, Daihatsu, Fuji, Honda, Mazda, Mitsuoka, Subaru, and Mitsubishi. Obviously they weren't in the Studebaker Museum exhibit, but some of these were sold in the U.S. and would be interesting to compare to the Europeans.
You raise some really good points, William K. Maybe I'm a bit too timid about crash safety. The only accident I ever had was 29 years ago, while sitting at a traffic light. The driver -- a 16-year-old who had gotten her driver's license two weeks earlier -- plowed into the back of my car at about 35 mph without ever touching the brakes. I hit the car in front of me, which hit the car in front of it. My car was totaled. If I had had back-seat occupants, I don't know if they would have survived. Looking at the Isetta, it scares me to think about that crash. As you point out, getting rid of the bad drivers (like that one) is the key. In the meantime, I'll probably continue my timid ways. I like crash energy absorption.
"Iso, which built the Isetta for BMW, also manufactured refrigerators. The company's refrigerator experience is said to have contributed to the Isetta's unique front door design."
I always wondered about that door... When I was about 6 someone gave me a die cast collection of these types of cars and the Isetta was one of them.
In the 70s I owned just about every type VW, a 60' Karmin Ghia, various Beetles, micro-buses. I almost bought a mid-50s bug once. And I had a fiberglass dune buggy on a beetle chassis.
Also had a 65' beetle with huge tires, no doors... or fenders that was for woods cruzin, and when it died we took the body off the frame and hung it from a tree, upside down... and made a swing out of it... Best fun car ever.
I saw a Kubblewagen in a museum in Germany, interesting but it didn't inspire any desire to own one. They were a true engineering marvels if you consider where they were designed to operate. The VW engine/drivetrain/suspension/chassis was truly revolutionary, with torsion bars, swing-arm suspension, magnesium castings, monocoque body, wide tolerances for ease of manufacturing, 4 passenger capability and overall robust nature.
@JimT -- The VWs were far more ubiquitous than microcars world wide, as well as in the US, so most folks nowadays are unfamiliar with them. Most microcars weren't officially imported here, and their combined production numbers (except for the FIATs) were a small fraction of Volkswagen's. Also, of course, the US car market isn't really a good match for tiny, slow, low-powered vehicles, even ones with great mileage.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
23 
