Guest Blogs

Petroski on Engineering: Checklists & Design

< Previous Page 2 / 2
View Comments: Newest First|Oldest First|Threaded View
<<  <  Page 2/3  >  >>
User Rank
Petroski on Engineering: Checklists and Design
FauEng   7/4/2012 8:58:23 AM
It is amazing how much and in how subtle ways cross-disciplinary approach can enhance quality, efficiency, safety... in any given faculty or field of human creation. Learning from each other, and not necessarily within the same science, is the way we progress as humankind. Although I am not saying much new here, in my view, these are important things to underline, and am thankful to a philosopher-engineer-designer who captured this importance in his article. For my part, I am in particular sensitive to one huge "check-list item" in design process: safety of those who are using, operating, or simply get exposed to a final result of design process.

User Rank
Re: Check-List Limits
dindyk   7/4/2012 12:40:52 AM
GUMPF??? what happened to 'B'. Brakes OFF?

in the UK it was always BUMPF(F):

Brakes OFF, Undercart DOWN, Mixture RICH, (Prop) Pitch FINE, Fuel SUFFICIENT FOR OVERSHOOT and ROUND AGAIN, Flaps SET for LANDING


Daniel I {PPL at age 17 and Chartered Professional Engineer (Elec)}

William K.
User Rank
Checklists in engineering
William K.   7/3/2012 7:28:16 PM
I have found it quite useful and valuable to use checklists both in quoting projects, so that we can be sure that we are pricing all of the steps between concept and completion, and also in the final installation of projects at a customers site, located someplace where forgotten items are unavailable.

In addition, the checlist, particularly the installation list, serves as a notification of what subset of skills will need to be on hand for the various stages of installation. That is not only a handy way to keep things moving, it is also a good way to limit the time that we need to have expensive specialists on site, such as pipline welders.

So checklists are quite a good value, although they require care to assure that nothing gets left off.

Charles Murray
User Rank
More lives at stake means better checklists
Charles Murray   7/3/2012 5:17:14 PM
It's amazing how much better a process gets when more lives are at stake. Multi-story buildings must be safe -- there are hundreds or thousands of lives inside -- and somehow the process improves. Same for big aircraft. When I worked in the nuclear power industry 30 years ago, all our engineering calculations were checked and signed by three engineers, and then by the utility, and then, presumably, by more people (who I was unfamiliar with) along the way. Somehow, processes get short-cutted when the consequences are less obvious. Surgery should be one of those areas where the consequences are obvious, but I suspect that mistakes are frequently made in the operating room that never come to light, and have no consequences at all.

Greg M. Jung
User Rank
Design Checklists
Greg M. Jung   7/3/2012 4:02:31 PM
To quickly and accurately create the best designs, I've found it best to use design checklists (written design guidelines) as I am designing.  These guidelines are baseed upon previously learned best practices (and also on making sure a previous error is not repeated again).  Some of these guidelines are more well-known like DFM (Design for Manufacturing), and some are more specific to the particular industry the product is being designed for.  All in all, written checklists/guidelines not only help our team get to market faster with a better product, they also teach and mentor less-experienced engineers and designs on how to quickly get up the design learning curve.  

User Rank
Check-List Limits
ab3a   7/3/2012 9:53:51 AM
In addition to practicing engineering, I have also been a licensed pilot for more than 20 years. There are three elements safety: Checklists, logical work-flows, and cross checks. 


Yes, have a checklist, BUT KEEP IT SHORT AND TO THE POINT! If it gets too long or too pedantic, people will ignore them, particularly under stress. When I first learned to fly, I used the official Pilot's Operating Handbook checklist for the aircraft. This is a legal document, often created with the assistance of hordes of nosy lawyers who probably didn't know a damned thing about aviation. There were some things that were checked two and three times and other things that could have been deadly to ignore, but weren't even on the list.


As I grew more comfortable with my aircraft, I developed my own checklist.  The pre-flight checklist is a biggie. To make it more intuitive and less cumbersome, I set it up to follow the path I would typically walk around the airplane. I didn't leave anything off, but I did add a few nusiance-if-they-break items at the appropriate places.


Next, my pre-taxi and pre-takeoff lists were relatively shorter, but still very performance based. These are verbal lists I hand the printed lists to my passenger/co-pilot to call out and I would respond in kind. Yes, I would memorize those lists.  As soon as I was in the air, the lists would be stowed with the red-striped emergency pages on top.  I had my navigation work all laid out with multiple resources to confirm where I was. Some of my waypoints might have been visual, some might use a beacon from an airport I was passing over, some might use GPS, and others an intersection of two VOR radials. The key is that I have a diversity of methods, so that I not get fixated on any one instrument.  I also keep a list of alternate airports at each stage of flight, just in case something goes wrong.


And finally, when it came time to land, I once again memorized the infamous GUMPF check-list: Gas, Undercarriage, Mixture, Prop, Flaps.  It is simple, stupid, and it works. I use it several times during various phases of landing. 


Airline pilots have developed what they call work-flows through the cockpit  Each task has a routine feel to it, each work-flow item follows the panel of the aircraft in some direction. Both pilot and co-pilot do this and confirm each other's work. 


What you see here is the use of SIMPLE checklists, logical work-flows, and lots of planning for likely contingencies.


All this training and practice came together several years ago.  I was flying as a safety pilot with a friend practicing instrument approaches. We discovered an engine problem at 4000 feet over a VOR west of Philadelphia at night.  Training took over. We landed safely with little fanfare. Later investigation showed a cracked cylinder on the engine.  Checklists do work, even under stress, but they have to be terse, simple, and to the point.


Jake Brodsky


User Rank
Re: Checklists naturally grow, with age
jbrac   7/3/2012 9:47:38 AM
I suspect that every engineer worthy of the name has a huge mental database of design checklists for the variety of components, systems, products, and processes he has encountered in his career. DFMEAs and PFMEAs are the checklists we use to check our checklists to make sure we haven't missed something that should have been foreseen. If done properly, they are valuable tools. However, we are always aware that "We don't know what we don't know.", and expect some unexpected surprises will occur before we are done. That is how the checklists grow.

User Rank
Re: I Agree There Is A Pattern
ervin0072002   7/2/2012 3:32:33 PM
When we redesign we review device requirements everytime and retest design. Its expensive however we do it right every time.

User Rank
Checklists naturally grow, with age
JimT@Future-Product-Innovations   7/2/2012 1:05:54 PM
I would offer that a naturally inherent "checklist" is a basic thought process of any reasonable skilled designer.  And for anyone who has had the responsibility of being a product architect over numerous lengthy projects, that checklist gets honed and refined, after every project.  It improves with age and experience.  Thinking back several decades to one of my earliest efforts, I can honestly say, (now) that I ran into situations I would never had even imagined could have happened – which today are a routine part of the design effort.  Yes, a Checklist.  I use one.  And even if an engineer doesn't have one printed out, they certainly have one framed mentally.  But I strongly contend that a literal, written, bulleted list of cautions is needed.  I wouldn't really be successful without one.

User Rank
Re: I Agree There Is A Pattern
tekochip   7/2/2012 11:02:09 AM
It can go both ways. I've seen cost reductions that improved the design by cleaning out attributes that were in the original design but no longer specified or used, and I've seen where something got changed that should not have because the new engineers were unaware of why something was done a particular way. Whenever possible I dig for the old notebooks to find why a design decision was made, just to make certain I'm not creating a problem that somebody already solved.

<<  <  Page 2/3  >  >>
Partner Zone
More Blogs from Guest Blogs
Practically all electronic devices today contain metals that may be coming from conflict-ravaged African countries. And political pressures will increasingly influence how these minerals are sourced and used in products.
Conformal coatings present themselves as space-saving alternatives to enclosures for protecting the circuit boards of automotive electronics. They can also provide electrical insulation.
Design for manufacturing (DFM) in mold production means that mold designers evaluate the manufacturability of their molds in the early stage of mold development by collecting all relevant information and applying it to their designs. They also have to consider many other factors, including flow balance, structural stress, and assembly tolerance, in order to ensure successful molding production.
Some adhesives provide strong structural bonds but take hours to fixture and attain handling strength. The technologies that offer the fastest cure do not bear loads or withstand stresses. A new class of adhesives aims to make both stick.
The continued growth of wireless health is a near-certainty. And engineers will be the key to developing and advancing technology solutions.
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Aug 8 - 12, Getting Hands On with Arduino Mechatronics
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9 | 10

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Technology Marketplace

Copyright © 2016 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service