HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Blogs
Guest Blogs

Combining Self- & Mutual-Capacitive Sensing for Distinct User Advantages

NO RATINGS
1 saves
Page 1 / 2 Next >
View Comments: Newest First|Oldest First|Threaded View
B1
User Rank
Iron
Touch screens - capacitive digitizer
B1   3/27/2015 9:35:00 AM
NO RATINGS
Very nice article. I replaced the touch screen on a cell phone ( Sony Xperia Z2)by using Optical Clear Adhesive( OCA)  and it works in a strange ways. e.g I click on one letter and it writes different or writes more than one . When I test it from a service menu it draws different line than it is correct.

I had tested that touch screen before gluing( using OCA ) and it worked well.

So I separated the touch screen and LCD  it again (by using a repair machine) and test it again and it worked ok. 

 Does it mean that by a pressure ( that OCA caused ),the function changed?

Or what is faulty in that touch screen?

Thank you for help

Shar N.
User Rank
Iron
Re: Capacitive Sensing
Shar N.   2/19/2014 4:39:46 PM
NO RATINGS
Thanks for the feedback everyone and glad you enjoyed the article! Regarding the question from User 78RPM- In mutual capacitance you scan all of the 'pixels' (or nodes in industry parlance) and convert capacitive measurements into digital. These are all stored in memory so you can make decisions in firmware as to which nodes represent fingers touching the screen. You can almost think of it as a topographical or 3D contour map of the screen with the X and Y axes representing position and the 'Z height' representing the capacitive signal. So the tallest peaks on the map represent likely finger locations. Of course you get complexities introduced from water droplets, palms resting on the screen, or hovering fingers that you want to report as hovering objects rather than touches, and so on. All of these need good algorithmic techniques to effectively reject them

 

In self capacitance you take of all these same capacitive measurements in each X and Y axis and you have a profile or a single measurement per trace. You can think of it as a bar chart with the height of each bar symbolizing the capacitive measurement. And the number of bars is the total of number of X and Y traces. You can then use a center of mass style calculation (or similar algorithm) that computes the X-position and Y-position of the finger. As you can see you're looking at each axis independently so you don't have a datapoint per node as you do in mutual capacitance but as the article illustrates there are benefits from self capacitance for power consumption, moisture immunity and first touch latency.

 

To answer your other question a single broken trace will cause a dead spot along that particular trace where the touchscreen will become unresponsive. The further along the trace (i.e.- farther from the routing channel and closer to the end of the trace) that break is located, the smaller the dead zone will be. If the trace breaks right where it routes into the touchscreen from the bezel edge then effectively the entire trace will become a deadzone. The remaining part of the touchscreen will be usable though. 

 

Shar Narasimhan (author)

Atmel Corporation

 

TJ McDermott
User Rank
Blogger
A VERY educational primer
TJ McDermott   2/5/2014 12:55:00 AM
NO RATINGS
Thank you for the lesson covering capacitive sensing touch screens.

78RPM
User Rank
Platinum
Re: Capacitive Sensing
78RPM   2/2/2014 1:15:57 PM
NO RATINGS
Help me understand, Shar or taimoortariq or anyone else.  I had always thought that all the capacitance pixels of a phone or tablet were mapped to memory addresses.  The article is telling me that there are only two circuits; the X and Y axes.  Then there is some kind of capacitance profile that identifies the spot that is touched. What is that algorithm or neural network like?

A secondary question: Is it possible that a single break in either the X or Y axis could cause a single point of failure for the whole device?

taimoortariq
User Rank
Gold
Capacitive Sensing
taimoortariq   1/31/2014 3:46:16 PM
NO RATINGS
I still remember the amount of effort we had to do with resistive touches, Thanks for the elaboration of the sentive screen Shar, The science behind the touch screens is indeed fascinating.

Partner Zone
More Blogs from Guest Blogs
“How can European standards affect me, especially since I only use machines built in the US?” This is a common question, and one way to answer this is to look at how machine safety is enforced, where the information comes from, and how well you can prove you followed the regulations.
In order to keep in line with safety protocols, industrial networks need to be filtered in a semantic way so that only information related to diagnostics is flowing back to the vendor and that any communications that could be used for remote machine operations are suppressed.
While people may talk about the procurement process, the procurement discipline actually encompasses a number of different processes. They include spend analysis, supplier relationship management, and contract management, just to name a few.
As the Industrial Internet of Things and machine-to-machine communications movements gain speed, some companies are asking themselves, “Wait. How much information do we really want to flow in and out of our premises? Aren’t we supposed to be doubling down on cyber security?”
To carry out the program, Boeing built five custom carriages using a custom, upgraded pneumatic rod lock system developed by Advanced Machine & Engineering Co.
Design News Webinar Series
5/21/2015 11:00 a.m. California / 2:00 p.m. New York
5/7/2015 11:00 a.m. California / 2:00 p.m. New York
6/3/2015 8:00 a.m. California / 11:00 a.m. New York
6/11/2015 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Jun 8 - 12, Everything You Ever Wanted to Know about Filters
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Course June 2nd-4th:
Sponsored by Proto Labs
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service