HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Blogs
Guest Blogs

Eraser or Sledge Hammer? You Decide

NO RATINGS
View Comments: Newest First|Oldest First|Threaded View
<<  <  Page 2/2
Tom Kramer
User Rank
Blogger
Re: What doesn’t work on paper will definitely not work in real life
Tom Kramer   12/18/2013 9:56:20 AM
NO RATINGS
The map of the house is a great analogy. Many details regarding the homeowners preferences need to be known before the construction crew starts building. Why do they wat the sink here, or over there? Where is the ceiling to be vaulted? Which direction do they want the staircase to face, and why? We need to know this stuff.

Sadly, so often we see a high amount of engineering effort go into product development before the "house plans" have been sketched in, even at a primary level.

Tom Kramer
User Rank
Blogger
Re: Fair Statement
Tom Kramer   12/18/2013 9:52:26 AM
NO RATINGS
Good point Nancy. Sometimes it is a matter of doing the most you can with the small amount of resourced available at the beginning of a project. This is just reality. And you are correct, WAY too many R&D people just think, "I would do it this way", or "this seems to work for me". These people may be from Mars, and actual users may be from Venus!

Nancy Golden
User Rank
Platinum
Fair Statement
Nancy Golden   12/18/2013 9:44:28 AM
NO RATINGS
"Finally, some people claim that doing design research puts too much restraint on their creativity. Ironically, a robust design research process actually gives you a lot of design freedom. Even better, it points you more directly to where the majority of all your creative energies should be focused, which can drastically increase product development efficiency and innovation."

I think this is a very fair statement. I would think the challenge is determining how much up front research is enough - striking a balance between the amount of research to be done and when to move into the next phase. Also, understanding your target audience is key - usability feedback must be from actual users rather than people from a generalized group that fall into a predefined category.

Habib Tariq
User Rank
Iron
Re: What doesn’t work on paper will definitely not work in real life
Habib Tariq   12/17/2013 7:46:34 PM
NO RATINGS
For example take civil engineering. You need to have the map of the house before you can actually start building it.

Plus in the middle of the project you may come up with better solutions and ideas to incorporate in it but if you haven't thought of them before, it might be too late to include them

Habib Tariq
User Rank
Iron
What doesn’t work on paper will definitely not work in real life
Habib Tariq   12/17/2013 7:46:02 PM
NO RATINGS
A very valid point you have made. What doesn't work on paper will definitely not work in real life. Plus a well-researched project does progress at a better rate and actually has a chance of making it to the finish line.

<<  <  Page 2/2
Partner Zone
More Blogs from Guest Blogs
Industrial workplaces are governed by OSHA rules, but this isn’t to say that rules are always followed. While injuries happen on production floors for a variety of reasons, of the top 10 OSHA rules that are most often ignored in industrial settings, two directly involve machine design: lockout/tagout procedures (LO/TO) and machine guarding.
Load dump occurs when a discharged battery is disconnected while the alternator is generating current and other loads remain on the alternator circuit. If left alone, the electrical spikes and transients will be transmitted along the power line, leading to malfunctions in individual electronics/sensors or permanent damage to the vehicle’s electronic system. Bottom line: An uncontrolled load dump threatens the overall safety and reliability of the vehicle.
While risk management sounds like one activity, in order to be conducted effectively, it must be broken down into three sub-components: risk assessment, risk monitoring, and response planning.
While many larger companies are still reluctant to rely on wireless networks to transmit important information in industrial settings, there is an increasing acceptance rate of the newer, more robust wireless options that are now available.
To those who have not stepped into additive manufacturing, get involved as soon as possible. This is for the benefit of your company. When the new innovations come out, you want to be ready to take advantage of them immediately, and that takes knowledge.
Design News Webinar Series
3/31/2015 11:00 a.m. California / 2:00 p.m. New York
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
12/10/2014 8:00 a.m. California / 11:00 a.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Mar 30 - Apr3, Getting Hands-On with Cypress’ PSoC
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  67


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service