HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Blogs
Guest Blogs

Thermodynamics of Panel Cooling

Page 1 / 2 Next >
View Comments: Newest First|Oldest First|Threaded View
Joe Panfalone
User Rank
Blogger
Re: Is it time for mil-spec in plants?
Joe Panfalone   8/19/2013 9:09:59 AM
NO RATINGS
EXAIR does have high temperature cabinet coolers. They are good for environments of 200 degrees F. They are of stainless steel construction so they are corrosion resistanct as well

Joe Panfalone
User Rank
Blogger
Re: Is it time for mil-spec in plants?
Joe Panfalone   7/25/2013 2:11:18 PM
NO RATINGS
thanks for catching that. I need to Rich correct that for us

ratkinsonjr
User Rank
Gold
Re: Is it time for mil-spec in plants?
ratkinsonjr   7/23/2013 9:16:04 AM
NO RATINGS
O.K., Thanks, I get it now. The bottom of the panel is one of the small (2ft2) sides. BTW, the superscript for ft2 was dropped during editing of the original article, so the areas are shown as ft instead of ft2.

Joe Panfalone
User Rank
Blogger
Re: Is it time for mil-spec in plants?
Joe Panfalone   7/23/2013 7:57:10 AM
NO RATINGS
Panel is 4' tall 2' wide and 1' deep

4*2 = 8 square feet surface area front

4*2 = 8 square feet surface area back

1*4 = 4 square feet surface left side

1*4 = 4 square feet surface lright side

1*2 = 2 square feet surface are top side

TOTAL surface area = 26 square feet

ratkinsonjr
User Rank
Gold
Re: Is it time for mil-spec in plants?
ratkinsonjr   7/22/2013 1:53:02 PM
NO RATINGS
I'm confused. In the example shown, there are three (3) dimentions for the panel area (2ftx4ftx1ft), but this should yield a volume (ft3), not ft2, as shown in the example. Assuming a rectangular prism with six (6) sides, there are two sides with 8ft2 each,two with 4ft2 each, and two with 2ft2 each, for a total surface area of 28ft2. Also, which side is the bottom surface that you are ignoring? Did I miss something? Please help.

Rob Spiegel
User Rank
Blogger
Is it time for mil-spec in plants?
Rob Spiegel   7/19/2013 12:58:14 PM
NO RATINGS
Nice article Joe. Quite enlightening. Is the potential solutioin to this mil-spec parts? Certainly ruggedized parts can better withstand high temperature even if they cost a bit more. 

Partner Zone
More Blogs from Guest Blogs
It seems that gears have been around forever -- what could be new?
The use of ZNE technology buildings not only reduces cost and creates renewable energy, but it can give a boost to the economy. The implementation and execution will require a workforce, which means the result can be increased employment.
The use of CFD is more profound in automobile design because of the diverse physics involved. It can be used to optimize components for downsizing and reducing the environmental footprint while maintaining or improving operational efficiency.
A Detroit automaker was struggling with a semi-manual, labor-intensive parts receiving process. Workers had enter parts into a spreadsheet manually at a stationary workstation. This stopped the receiving process dead in its tracks. A better system was needed.
Pressure sensors can be used in a wide range of applications. It’s imperative that they’re suited for use in hazardous situations and are fully compliant with one of several protection standards.
Design News Webinar Series
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
7/17/2014 11:00 a.m. California / 2:00 p.m. New York
6/25/2014 11:00 a.m. California / 2:00 p.m. New York
5/13/2014 10:00 a.m. California / 1:00 p.m. New York / 6:00 p.m. London
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Aug 4 - 8, Introduction to Linux Device Drivers
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Class: August 12 - 14
Sponsored by igus
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service