The legacy endpoint devices that control our critical infrastructure (utility systems, water treatment plants, military networks, industrial control systems, etc.) are some of the most vulnerable devices on the Internet. These devices present a vast attack vector thatís not adequately protected. Many of these are:
fixed-function devices that canít be upgraded to add security;
devices that use obsolete operating system (OS) versions that are insecure and canít be upgraded;
real-time OS-based devices that were designed before security was a critical concern and therefore lack sufficient security;
designed for use on private networks but are now connected to the Internet.
Once deployed, these devices remain in use for five, 10, or even 20 years. The cost to replace them all to add security improvements would be staggering. For devices that canít be easily or affordably replaced or upgraded, a ďbump-in-the-wireĒ appliance solution provides the required security.
Some OEMs offer products to protect these legacy devices by creating a ďsecure enclaveĒ in which these devices can operate. Only trusted devices should be deployed within the secure enclave. These devices can freely communicate with each other; however, communication outside of the enclave is controlled for security. The bump-in-the-wire appliance provides security by enforcing communication policies, ensuring that only valid communication is allowed with the endpoints within the secure enclave.
By limiting communication to the secure enclave, the bump-in-the-wire appliance will:
Prevent probes and hacking drones from discovering endpoints. Hackers and automated drones send out ping requests or other messages to a range of IP addresses looking for responses. The appliance drops these requests making the endpoints undiscoverable.
Prevent access from unauthorized machines. Many fixed function devices only need communicate with a few known, trusted hosts. Enforcing these communication restrictions prevents communication with unauthorized machines. If a hacker canít communicate with the endpoint, they canít compromise it.
Close security loopholes. Many cyberattacks utilize services on an endpoint that arenít required for fixed function devices. Blocking unused ports and protocols closes these commonly exploited security loopholes.
Protect against denial of service attacks. By controlling whom the endpoint talks to, DoS attacks are blocked before they reach the endpoint. The endpoints are shielded from malicious traffic and traffic floods, ensuring continued operation even when the network is under attack.
Protects against insider attacks and malware on the corporate network. Endpoints within the secure enclave are sheltered from malicious packets that may be present on the corporate network. With communication restricted to a small set of trusted hosts, malware, insider attacks, or any other malicious activity is blocked. An insider attempting to hack an endpoint from outside the corporate network or from any non-trusted machine will also be blocked, preventing the attack.
Quarantine infected or compromised machines. If the appliance provides bidirectional filtering, it will enable any endpoint infected with malware or compromised by hackers to be quarantined, limiting damage from the attack.
Enhance security for endpoint devices. Fixed function devices, SCADA machines, and other critical endpoints can be grouped into a secure enclave. The communication policies for these machines can be more restrictive than the general policies for the rest of the network. This allows a higher level of security to be enforced for the critical devices on your network. Even if the front end of the corporate network is breached, the individual endpoints are still safe.
The main difference is that our solution will support all TCP/IP traffic, not just HTTP traffic. Our solution also supports flexible filtering rules that can be customized for SCADA and similar devices.
Practically all electronic devices today contain metals that may
be coming from conflict-ravaged African countries. And political pressures will increasingly influence how these minerals are sourced and used in products.
Design for manufacturing (DFM) in mold production means that mold designers evaluate the manufacturability of their molds in the early stage of mold development by collecting all relevant information and applying it to their designs. They also have to consider many other factors, including flow balance, structural stress, and assembly tolerance, in order to ensure successful molding production.
Some adhesives provide strong structural bonds but take hours to fixture and attain handling strength. The technologies that offer the fastest cure do not bear loads or withstand stresses. A new class of adhesives aims to make both stick.
Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies.
You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived.
So if you can't attend live, attend at your convenience.