HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Blogs
Guest Blogs

Plasma: A Cut Above the Rest

NO RATINGS
View Comments: Newest First|Oldest First|Threaded View
Page 1/2  >  >>
RichardBradleySmith
User Rank
Silver
Plasma looks great
RichardBradleySmith   2/9/2013 2:03:01 PM
NO RATINGS
But when I needed a beer brewing kettle (I forget what they are called) I used a saber saw to take the top off a discarded keg. I used the same saw to round some corners on wood shelves the other day. To the point, I have two ten year old boys. I am not teaching them about bandsaws or plasma, everything today is vacuumed bagged and mostly carbon fiber. Although I must say a carbon fiber bridge, now that may not fly.

Need plasma? Go to your your local machine shop.

Cabe Atwell
User Rank
Blogger
Re: About to buy one...
Cabe Atwell   2/8/2013 4:51:08 PM
NO RATINGS
Yes, CNC plasma cutter prices are out of this world. I am surprised someone hasn't taken those portable plasma cutters ($500) and combined it with a CNC router (some at $500 as well). Perhaps it is due to the frightening accidents that could happen? Or the routers not able to withstand the heat? I don't think I would want to use a DIY/hobbyist made CNC plasma cutter for those reasons.

 

C

streetrodder
User Rank
Gold
About to buy one...
streetrodder   2/6/2013 10:59:42 AM
NO RATINGS
I guess I'm about to qualify as a serious hobbyist.  You can tell by my tag what one of my hobbies is.

In street rodding, plasma has become the preferred cutting method, especially for sheet metal.  The minimal heat distortion and accuracy reduce the amount of 'massaging' needed to realign the metal.  This is particularly important when chopping or sectioning the body. 

As it looks like I'll be 'slicing and dicing' a '32 Chevy sedan next, it's time for me to buy a plasma cutter.

jf
User Rank
Iron
Re: Plasma cutting
jf   2/6/2013 9:59:36 AM
NO RATINGS
I have not experienced significant distortion when making plasma cuts.  Quite the opposite.  The plasma jet is *so* hot and so localized that the work material is liquified and blown out of the cut before the remainder of the work piece can be affected.  Anything that touches the plasma is removed, and anything not touched by plasma is left behind.  Overall heating of the piece is much less compared to cuts using an oxy/fuel process.  On thinner material (<1/4") you can *almost* handle the pieces within a few seconds of completing the cut, though obviously that is not recommended practice.  The kerf (width of cut) is also significantly smaller than with oxy/fuel, and the cutting time is less as well.

For what it's worth, the History Channel has a Modern-Marvels episode where they show 3" steel plate being cut by robotic plasma cutter at the Newport-News shipyard.  The plate is actually submerged under water to suppress the fumes and ensure there is no thermal distortion, which would be impossible with an oxy torch.

Gorski
User Rank
Platinum
Plasma cutting
Gorski   2/5/2013 5:36:32 PM
NO RATINGS
While this method sounds like it has promise, one thing stuck in my mind. The plasma stream is energized and creates heat. Is the heat high enough to distort the workpiece? If so, this would affect the aciracy of parts produced by this process.

 

GORSKI PE

Gorski
User Rank
Platinum
Plasma cutting
Gorski   2/5/2013 5:36:32 PM
NO RATINGS
While this method sounds like it has promise, one thing stuck in my mind. The plasma stream is energized and creates heat. Is the heat high enough to distort the workpiece? If so, this would affect the aciracy of parts produced by this process.

 

GORSKI PE

William K.
User Rank
Platinum
The plasma cutter
William K.   2/4/2013 8:56:06 PM
NO RATINGS
Aside from the quite toxic fumes, which I had not considered, a plasma cutter is quite hazardous due to the very high temperature plasma, which is able to deliver a whole lot of heat energy to almost anything almost instantly. So while they can produce very good cuts, it is mandatory to keep in mind the whole process at all times. There are lots of ways to get into trouble very fast when using a plasma cutter. This article did address a few of them.

bob from maine
User Rank
Platinum
Re: Cost effect
bob from maine   2/4/2013 5:45:05 PM
NO RATINGS
Cabe; I haven't found a Laser cutter anywhere near the 'affordable' range for a home hobbyist or a small shop. Plasma works well, but is fairly expensive, it only works where there is power and compressed air, and it only cuts. I've gone back to oxy/acetylene. I use it for cutting, heating, brazing and occasionally welding where power isn't available. The edges always need grinding using hand held Plasma or oxy. The major benefits of plasma are the ability to cut stainless, starting holes in the middle of a sheet or piece of pipe, the narrow kerf, relatively clean cut and less heat distortion. If I was running a shop, I'd use plasma for every possible cut but as a hobbyist I can't justify the space or cost.

jf
User Rank
Iron
Re: Cost effect
jf   2/4/2013 11:57:51 AM
NO RATINGS
In the past several years, economical rigs from Hypertherm, Miller, and others have started to make plasma-cutting affordable to home/hobby users.  I have a 60-Amp unit that works fine on plate steel up to around one inch.  One safety consideration that new users must not forget is a good respirator.  Even when cutting ordinary steel, the plasma process produces a fog of microscopic rust particles that is miserable to breath.  Users should visit their local welding-supplier and consider purchasing a disposable N95 welding-fume respirator.  I wear eyeglasses so I prefer a respirator with a valve (eg 3M #8515) so moisture does not fog my lenses when I exhale.  If I cut any galvanized steel, then I also rely on the welding respirator to filter out any zinc particles which are known to cause "metal fume fever" if inhaled.  Anyone cutting stainless steel should be aware that the plasma process creates "hexavalent chromium" particles, and anybody who saw the film "Erin Brockovich" can relate to what chromium-six does to people, so stainless-cutters will want to have respirators that are rated for hazardous materials such as chromium.  I use a 3M #8212 in this case.  I have listed my personal preferences (from 3M) but several other manufacturers offer suitable products as well.  I buy them in small quantities from my local welding supplier for under $20 each, a small price compared to the expense of treating bronchitis, or worse, cancer.

Larry M
User Rank
Platinum
Re: Cost effect
Larry M   2/4/2013 9:36:36 AM
NO RATINGS
Hmm. They seem to be available on Amazon, Harbor Freight, and eBay. Affordable for the serious hobbyist, I would say.

Page 1/2  >  >>
Partner Zone
More Blogs from Guest Blogs
More often than not, with the purchase of a sports car comes the sacrifice of any sort of utility. In other words, you can forget about a large trunk, extra seats for the kids, and more importantly driving in snowy (or inclement) weather. But what if there was a vehicle that offered the best of both worlds; great handling and practicality?
As additive manufacturing (including 3D printing) becomes increasingly popular among businesses as a quick and easy solution to creating and evaluating prototypes and end-use products, the debate about whether to outsource production or to purchase equipment for in-house use is at the forefront of industry discussions.
With increasing terrorist threats overseas, organizations are thinking about how best to defend themselves here and abroad. Engineering can play a role, especially when it comes to putting a barrier between yourself and the bad guys.
Time to market is everything, but at the same time, you cant sacrifice quality for speed. Thats where additive manufacturing comes into play.
In the last few years, use of CFD in building design has increased manifolds. Computational fluid dynamics is effective in analyzing the flow and thermal properties of air within spaces. It can be used in buildings to find the best measures for comfortable temperature at low energy use.
Design News Webinar Series
10/7/2014 8:00 a.m. California / 11:00 a.m. New York
9/25/2014 11:00 a.m. California / 2:00 p.m. New York
9/10/2014 11:00 a.m. California / 2:00 p.m. New York
7/23/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Nov 3 - 7, Engineering Principles behind Advanced User Interface Technologies
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Last Archived Class
Sponsored by Littelfuse
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2014 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service