Workplace ergonomics is getting a lot of nationwide attention in response to a sharp increase in incidents of repetitive-strain injuries resulting in musculoskeletal disorders, such as carpal tunnel syndrome. Occupational diseases often mean repeated surgery, intractable pain, inability to work, time off for the affected employee and, ultimately, higher costs for the employer.
Below are four steps a company can take to address this growing problem.
Review tasks for risk factors: The first step to correcting problems is to understand the key workplace ergonomic risk factors, and review work tasks in your operation to see which ones apply. This can make a tremendous difference, since occupational safety professionals estimate that reducing physical stresses could eliminate as much as half the serious injuries that happen each year.
Control risk factors with engineering and administrative controls, and personal equipment, where it is effective: Engineering controls to improve ergonomic risks may include changing the way parts and materials are transported, or changing the process to reduce how workers are exposed to risk factors.
Understand how to make the work space work ergonomically: With any task, selecting the proper tool is crucial. The key is to understand the work process and employee’s safety needs. After identifying the likely risk factors in an operation, develop a safer work environment by carefully selecting the tools and work stations workers will use.
Use work station design principles to improve ergonomics: The following strategies typically yield safe work environments: make the work station adjustable, locate materials to reduce twisting, avoid static loads and fixed work postures, set the work surface to the particular task, provide adjustable chairs, allow workers to alternate between standing and sitting, support the limbs, use gravity, design for proper movements, consider computer monitors, provide simple dials and displays, and consider overall environmental conditions.
A project starts with whatever technology is available at the time, so if it's the latest and greatest at the time, it's not exactly out of date. As I said, LEAP came out after they'd already started. And obviously, they don't think it's better than Kinect, at least for their project. Lots of people would agree with them: it depends on the project, and is often simply a matter of preference.
Ann next-gen system. Why start a project with out of date equipment. Isn't LEAP supposed to be so much better than the kinect? If they aren't even done with it why use old tech? It'll be out of date before it's launched.
Cadman-LT, the researchers described in that article said their next-gen system would use Kinect. At the time, LEAP either wasn't out yet, or had just been announced.
Is that what those things are for Ann? I've seen a number of people using those bands, but I could never figure out what they were used for...and didn't want to seem that nosy by asking. I'll have to keep that in mind.
At CES 2012 and 2013 I saw a log of those reclining chairs with monitors suspended around them. You lay back like a dentist’s operating chair. Is that good? It seems like it take all the strain off the body, while at the same time making it weak. Reminds me of the chair the “genius” programmer from the movie “Grandma’s Boy” sat in.
C
Thanks, Cadman-LT. That makes more sense. Regarding the article, the motion-capture tape was used initially for testing the software's accuracy in controlling a virtual robot, as the article states. The next-gen system will use Kinect to control an autonomous robot.
An analysis of what’s needed to implement Design for Disassembly and Design for Recycling results in eight strategies engineers can use to design an intentional end-of-life stage into their products.
Government regulations, coupled with growing consumer sensitivity about data and identity theft, require that data storage organizations demonstrate proper protection and due diligence in protecting sensitive information stored inside datacenter enclosures.
When a crane doesn't have a monitoring system, crane owners schedule service every six months and simply scrap the parts they replace, even if a part has had little use and doesn't need replacing. This can cost thousands.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
9 
