HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Blogs
Guest Blogs
Focus LED Design on Driver Topology, Circuit Protection
12/19/2012

An isolated single-stage flyback driver (top) and a non-isolated buck driver. (Source: ON Semiconductor)
An isolated single-stage flyback driver (top) and a non-isolated buck driver.
(Source: ON Semiconductor)

Return to Article

View Comments: Newest First|Oldest First|Threaded View
William K.
User Rank
Platinum
Re: Led Drivers suffer from bigger problems
William K.   12/21/2012 3:04:03 PM
NO RATINGS
Please don't incriminate me with that all-inclusive "WE". Marketing types decide what will be on the shelves and they never ever listen to what I say. 

Of course there is a valid reason for putting LED emitters and supplies in a bulb-looking package, which is that until very recently those bulbs were the only show in town, and the luminairs that used them were what there was. So there exists a massive installed base of edison based light sockets, and that is where a whole lot of the replacements must fit. While change delivering an improvement is good, not everybody is ready to scrap all their present lighting and replace every bit of it with new LED systems. So the present obstacle is the current installed infrastructure, and that will not go away rapidly, no matter what congres legislates.

While it is not reasonable to manfdate a lower price, it certainly should be possible to mandate a minimum lifetime, and simply not allow products of inadequate quality to be sold for any price. OF course, determining that a product has an adequate lifetime would be a bit of a challenge, no question about that. But assuring adequate product life is the best way to gain acceptance.

Cabe Atwell
User Rank
Blogger
Re: Temperature
Cabe Atwell   12/20/2012 3:04:15 PM
NO RATINGS
Yes, the board may go out, but the LED, not so. In this circuit, it looks like the fuse is before the rectifier. I would assume it to be large enough to remove or change. Every company that would deal with such a device should have someone adept enough to at least open a box.

Don't count people out so quickly.

C

g-whiz
User Rank
Gold
Re: Temperature
g-whiz   12/20/2012 10:46:17 AM
NO RATINGS
@TJ McDermott 

I have also seen what you have observed. In my experience, it is the LED driver that fails and not LEDs themselves. We've still got a long way to go in driver design.

g-whiz
User Rank
Gold
Re: The downside
g-whiz   12/20/2012 10:40:23 AM
NO RATINGS
 

@Cabe

Most likely, the "fuse" will be a tiny, surface mounted device the size of a Tic-Tac and buried inside a non accessable cavity. Even if you could mange to get to the fuse, the replacement is only available by the 1000 piece reel from a mainstream electronics distributor.

g-whiz
User Rank
Gold
Led Drivers suffer from bigger problems
g-whiz   12/20/2012 10:26:18 AM
NO RATINGS
   While safety and circuit protection are two important aspects in the overall design, todays mainstream LED drivers suffer from (IMHO) two BIG problems - low efficiency and bad location. Most of the drivers I've seen have horrible power factors and efficiencies in the 70% range. How in the world can we be promoting LED technology with its huge efficiency gains and think a 30% loss in power conversion is acceptable.

   Furthermore, Why do we continually "shoehorn" this inefficient converter into a tiny little oven heated by the LEDs. All because we insist on making this "new" technology appear like a 100 year old A19 light bulb.

   We need to get the electronics package out and away from the LEDs. It can then be larger, cheaper, operate cooler so it will last longer, and perhaps employ user replaceable circuit protection devices.

 

tekochip
User Rank
Platinum
Re: The downside
tekochip   12/20/2012 7:34:51 AM
NO RATINGS
For the average consumuer; the bulb in your bedroom lamp burns out, you throw it away and buy a new one.

Cabe Atwell
User Rank
Blogger
Re: The downside
Cabe Atwell   12/20/2012 1:28:09 AM
NO RATINGS
Tekochip,

Great observation. Do you really think the end-user will toss the board? Isn't the fuse easy to replace after all?

C

TJ McDermott
User Rank
Blogger
Temperature
TJ McDermott   12/20/2012 12:23:05 AM
NO RATINGS
I think the assemblies are also susceptable to temperature swings - The traffic signals in North Charlston SC are LEDs, and most them have signifcant failures.  In some cases, more than 60 percent of the LEDs in a single color have failed.  Either that, or North Charleston got incredibly ripped off by whomever sold them the LED signals.

tekochip
User Rank
Platinum
The downside
tekochip   12/19/2012 1:48:00 PM
NO RATINGS
The dowside of using a fuse in a consumer application like this is that the fuse will never be replaced.  Once the fuse opens the product will not be repaired by the consumer and the device will end up in the garbage.  Yes, the fuse is reliable and inexpensive, but it really provides no protection for the rest of the circuitry because the entire device will be disposed of when the fuse opens.

Partner Zone
More Blogs from Guest Blogs
Was Steve Job’s signature outfit of a black turtleneck, jeans, and sneakers the secret behind his success? Maybe, or maybe not, but it was likely an indication of a decision-making philosophy that enabled him to become one of the most successful innovators of all time.
Electromechanical actuators and propulsion system enable the first controlled landing and ascent from a solar system body other than the moon.
Combining energy-saving product design and advanced lithium batteries enables wireless devices to operate maintenance-free for up to four decades.
Hardware-in-the-loop test platforms enable manufacturers to deal with increasing software complexity.
Remember when design decisions for optimizing low-power MCU applications were simple? All you needed to do was select when to put the MCU into the low-power mode and when to wake it up. Once it was awake, you just ran the required code as quickly as possible. Simple, right? Well, these days designing for power efficiency isn’t so simple. Why is that the case?
Design News Webinar Series
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
12/10/2014 8:00 a.m. California / 11:00 a.m. New York
11/19/2014 11:00 a.m. California / 2:00 p.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Feb 23 - 27, Baremetal C Programming for Embedded Systems
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  67


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service