HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Blogs
Guest Blogs

Design Decisions: What Designers Need to Know About EMI Shielding

View Comments: Newest First|Oldest First|Threaded View
Greg M. Jung
User Rank
Platinum
Thermal Management
Greg M. Jung   12/25/2012 3:40:46 PM
NO RATINGS
I agree that sometimes a completely enclosed metal box must be used. In these cases, more expensive heat pipes and heat sinks can also be used for thermal management.

Cabe Atwell
User Rank
Blogger
Re: More valuable info is necessary...
Cabe Atwell   12/7/2012 6:20:16 PM
NO RATINGS
Almost everything the military and NASA designs is in a metal enclosure afterward. It is fairly common practice to do so, I have found. I place a lot of my more sensitive projects inside a metal box routinely. So often the 60hz at the wall has been an issue with my testing, it was a necessity after.

C

gamzoom
User Rank
Iron
Re: More valuable info is necessary...
gamzoom   12/6/2012 11:14:29 AM
              Sizing Honeycomb EMI Shielding  - Broader implications.

This is a new concept for me and I can't help think about the wider implication of extending the principles to portable items and weatherproof vehicles.

In aircraft and outdoor portable units a small bore honeycomb would be vulnerable to water ingress due to capillary action. Exhaust blown air would help remove damp and condensation moisture but any air intake would be vulnerable. There would also be the issue of corrosion in residual trapped water in untreated copper or aluminum honeycomb. This could set some minimum diameter guideline.

The other out-door issue common to aircraft owners, is the minimum diameter of openings that resist the entry of insects. At certain time of the year insects find tubular openings that they can enter. They make silky nests for their larvae to grow in and can obstruct critical airflow. The maximum diameter seems to be about 0.125", which must be too small for a wasp's whiskers and head.  

In common households, and maybe some industrial environments, there is the problem of dust accumulation. Think of the PC CPU cooling fins that get clogged with dust (and fine cat hair if you are a pet lover). Again with input airflow, smaller orifices attract more significant obstruction over time.

So there seems to be some mechanical Max/Min guidelines to consider in a non-sterile existence.

I wonder what has been the experience of the Laser printer manufacturers with their honeycomb blocks. This maybe synthetic, thermally and electrically non-conductive material though. Would plated plastic work?

gamzoom. 

Amclaussen
User Rank
Platinum
More valuable info is necessary...
Amclaussen   12/5/2012 3:44:49 PM
Although the short article invites to see this matters in more detail, a little more info would be appreciated...

Like: Comparing between std. aluminum vs. copper enclosures, can we use thicker aluminum wall enclosures, or using a copper layer or sheet under the aluminum box acomplish a better result? Then, how thick?...  Are there any thumb rules regarding ventilation hole sizes/pitch and area, size of the perforated section? Location of perforated areas? and so on.  Amclaussen.

Partner Zone
More Blogs from Guest Blogs
Load dump occurs when a discharged battery is disconnected while the alternator is generating current and other loads remain on the alternator circuit. If left alone, the electrical spikes and transients will be transmitted along the power line, leading to malfunctions in individual electronics/sensors or permanent damage to the vehicle’s electronic system. Bottom line: An uncontrolled load dump threatens the overall safety and reliability of the vehicle.
While risk management sounds like one activity, in order to be conducted effectively, it must be broken down into three sub-components: risk assessment, risk monitoring, and response planning.
While many larger companies are still reluctant to rely on wireless networks to transmit important information in industrial settings, there is an increasing acceptance rate of the newer, more robust wireless options that are now available.
To those who have not stepped into additive manufacturing, get involved as soon as possible. This is for the benefit of your company. When the new innovations come out, you want to be ready to take advantage of them immediately, and that takes knowledge.
Design engineers will feel like kids in a candy store with the Cypress Semiconductor BLE Pioneer Kit. The development kit for low-power sensor-based systems is full of wireless wonder and exploration.
Design News Webinar Series
3/31/2015 11:00 a.m. California / 2:00 p.m. New York
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
12/10/2014 8:00 a.m. California / 11:00 a.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Mar 30 - Apr3, Getting Hands-On with Cypress’ PSoC
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  67


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service