Guest Blogs

Optically Isolated Relays Can Handle Industrial Systems, Too

View Comments: Oldest First|Newest First|Threaded View
User Rank
Go solid state
naperlou   11/1/2012 11:57:31 AM
Whenever a solid state component is available it will generally be superior to an electromechanical one in most modern applications.  I ran into this years ago with amplifiers for communications for satellites.  Typically klystron tubes were used.  Advances in solid state amplifiers allowed the replacement of these in many cases.  They were more reliable, lighter and used less power.  I see the same thing with this class of relay.  They also, as is pointed out, avoid some of the pitfalls of electromechanical relays.  There was an article in Design News about a problem with such a relay recently. 

User Rank
Re: Go solid state
akwaman   11/2/2012 10:21:32 AM
 I couldn't agree with you more, naperlou. Solid state is the way to go whenever is makes sense, as far as I'm concerned. In noise sensitive data aquisition matters, electromechanical relays can introduce unwanted noise into a system.  These kinds of optical relay technology has many uses.  Of course the obious power savings is a plus as is the reliability factor.

User Rank
Re: Go solid state
mrdon   11/3/2012 11:09:23 PM
akwaman, Nicely explained, I agree totally with all the points you've made. I wanted to use SSRs(solid state relays) in wireless Hunter Fan Ceiling Controls but management was against it because of cost. As you discussed in your post, yes the intial cost investment is somewhat pricey but the ROI would have been substantial in terms of reduced customer warranty claims due to failing electromechanical relays. I'm definitely will be sharing this article with my Control Systems class at ITT Tech.

Partner Zone
More Blogs from Guest Blogs
Practically all electronic devices today contain metals that may be coming from conflict-ravaged African countries. And political pressures will increasingly influence how these minerals are sourced and used in products.
Conformal coatings present themselves as space-saving alternatives to enclosures for protecting the circuit boards of automotive electronics. They can also provide electrical insulation.
Design for manufacturing (DFM) in mold production means that mold designers evaluate the manufacturability of their molds in the early stage of mold development by collecting all relevant information and applying it to their designs. They also have to consider many other factors, including flow balance, structural stress, and assembly tolerance, in order to ensure successful molding production.
Some adhesives provide strong structural bonds but take hours to fixture and attain handling strength. The technologies that offer the fastest cure do not bear loads or withstand stresses. A new class of adhesives aims to make both stick.
The continued growth of wireless health is a near-certainty. And engineers will be the key to developing and advancing technology solutions.
Design News Webinar Series
10/1/2015 11:00 a.m. California / 2:00 p.m. New York
9/10/2015 11:00 a.m. California / 2:00 p.m. New York
8/13/2015 11:00 a.m. California / 2:00 p.m. New York
10/20/2015 8:00 a.m. California / 11:00 a.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 5 - 9, Standards for the Internet of Things (IoT)
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service