HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
  |  REGISTER  |  LOGIN  |  HELP
Blogs
Guest Blogs

The Fight for the Perfect Fit

NO RATINGS
Page 1 / 2 Next >
View Comments: Threaded|Newest First|Oldest First
NadineJ
User Rank
Platinum
Enlightening
NadineJ   10/4/2012 11:02:24 AM
NO RATINGS
I didn't know there was any difficulty with mass customization for mouth guards.  This is interesting.

Thanks for showing how the new 3D technologies have helped this progress.

Beth Stackpole
User Rank
Blogger
Re: Enlightening
Beth Stackpole   10/4/2012 11:17:57 AM
NO RATINGS
3D scanning is a critical part of this whole effort. With it, companies like Fight-Bite no longer have to go through the time consuming and messy mold making process required by mouth guards and other products. The customization angle is huge--that's why this has traditionally been a manual, one-off development process.

Bob Cramblitt
User Rank
Iron
Re: Enlightening
Bob Cramblitt   10/5/2012 1:22:04 PM
NO RATINGS
Beth is correct. The current manual process is tedious, messy and time-consuming. This is a natural application for 3D scanning and digital processing.

Ann R. Thryft
User Rank
Blogger
Re: Enlightening
Ann R. Thryft   10/4/2012 11:57:27 AM
NO RATINGS
I'm waiting with bated breath for this to come to dentists for mouth-guards. Two weeks, the standard time for making them from molds, is much too long if you're having trouble sleeping due to snoring or teeth grinding.

Bob Cramblitt
User Rank
Iron
Re: Enlightening
Bob Cramblitt   10/5/2012 1:23:45 PM
NO RATINGS
I fully expect this to extend to dental practices, Ann.  The company that is working on this process, eQuality Tech, has extensive dental experience.

Charles Murray
User Rank
Blogger
Re: Enlightening
Charles Murray   10/4/2012 8:56:11 PM
NO RATINGS
I agree, NadineJ. The traditional method for making a mountguard was to bite into a a mouthguard filled with a soft gel, then let it harden overnight. Could this be much better?

Ann R. Thryft
User Rank
Blogger
Re: Enlightening
Ann R. Thryft   10/5/2012 12:11:38 PM
NO RATINGS
Chuck, the type you mention is pretty old, just past the ones you heat in boiling water and bite into. The next stage, which comes before the one described in this article, is what I've got. I bite into some truly disgusting gloppy pink stuff in a form and almost choke on it for a minute or two while it's hardening--but that's only the mold. Then I wait two weeks while a lab does I don't know what--twiddle their thumbs?--and then I get the clear plastic, looking just like the one in the photo to this story. The one described here would be a lot better than what I've got for the speed alone, and much better than the earlier-stage ones (I've used them, too).

Robbie1
User Rank
Iron
It's amazing how much dental care
Robbie1   7/28/2014 9:05:10 AM
NO RATINGS
It's amazing how much dental care has evolved over the years, this is yet another revolution in dental health. We all want better teeth, you can learn more here about ways to keep them clean and healthy, there really isn't any excuse for bad teeth anymore considering the online resources we all have access to.

Partner Zone
More Blogs from Guest Blogs
Transient-voltage-suppression diode technology eliminates surges and enhances vehicle safety.
Industrial workplaces are governed by OSHA rules, but this isn’t to say that rules are always followed. While injuries happen on production floors for a variety of reasons, of the top 10 OSHA rules that are most often ignored in industrial settings, two directly involve machine design: lockout/tagout procedures (LO/TO) and machine guarding.
Load dump occurs when a discharged battery is disconnected while the alternator is generating current and other loads remain on the alternator circuit. If left alone, the electrical spikes and transients will be transmitted along the power line, leading to malfunctions in individual electronics/sensors or permanent damage to the vehicle’s electronic system. Bottom line: An uncontrolled load dump threatens the overall safety and reliability of the vehicle.
While risk management sounds like one activity, in order to be conducted effectively, it must be broken down into three sub-components: risk assessment, risk monitoring, and response planning.
While many larger companies are still reluctant to rely on wireless networks to transmit important information in industrial settings, there is an increasing acceptance rate of the newer, more robust wireless options that are now available.
Design News Webinar Series
3/31/2015 11:00 a.m. California / 2:00 p.m. New York
2/25/2015 11:00 a.m. California / 2:00 p.m. New York
12/11/2014 8:00 a.m. California / 11:00 a.m. New York
12/10/2014 8:00 a.m. California / 11:00 a.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Mar 30 - Apr3, Getting Hands-On with Cypress’ PSoC
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  67


Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service