Guest Blogs

Fluid Power Systems: The Hidden Giant

View Comments: Newest First|Oldest First|Threaded View
User Rank
GlennA   6/20/2012 8:43:31 AM
An unloading valve is not the same as a relief valve or a regulating valve.  From my training:  An unloading valve is used to direct all flow from the pump to the tank at low pressure to reduce heating, and to allow the electric motor / pump to start under no-load.  A relief valve is used to control maximum system pressure.  When the maximum pressure is reached, the valve opens to direct flow to the tank without reducing the pressure.  A pressure reducing valve, also called a regulating valve, is used to reduce pressure to a segment of the system.  Not everyone that works in hydraulics agrees with the nomenclature that I learned.

Instead of a variable speed motor, I have seen pressure and flow compensating pumps that have a swash plate that is adjusted to reduce the flow from the pump without affecting the pressure, at a constant electric motor speed.

User Rank
Re: hydraulics vs working applications
crob09   6/19/2012 4:44:37 PM
No you still need an "unloading valve" or Bypass valve, no different from an electric forklift. The PTO is variable speed and the unloading valve is still necessary when the load is too great, or if the cylinder has reached it's maximum travel. Otherwise you would burn out the PTO or motor.



User Rank
Re: hydraulics vs working applications
Alex.W   6/19/2012 1:51:55 PM
I think the variable speed drive would negate the need for an unloading valve, assuming there were no other loads requiring driving while this subset of the machine is in standby.

TJ McDermott
User Rank
Each has its place
TJ McDermott   6/18/2012 1:57:58 PM
Hydraulic vs. Electric is not a winner-take-all competition.  Each has roles in which it is better suited.  One of my customers offers products that use either one or the other as the prime mover, depending on application.  It means more engineering work for my customer, but their end users are happy with a solution that fits their needs, rather than adjusting their needs to fit a single solution.


User Rank
hydraulics vs working applications
GlennA   6/18/2012 9:34:11 AM
Hydraulic robots have become few and far between (in my experience).  The rationale that I was told was because of the automotive industry.  Automotive is a big user of robots.  When robots were hydraulic, 3 (sometimes 4) trades were required to work on them.  The electrician for the controller, the millwright for the hardware, or for tooling issues (sometimes a tool-maker also), and a plumber for the hydraulics.  The all-electric robot eliminated one trade from that group.

The manipulator arm on the Space Shuttle was a 'hydraulic' application = high torque and low speed.  Clean-room issues i.e. hydraulic oil leaks would have been a problem.  A broken wire does not 'leak' electricity in the same way a broken hose would leak oil.

One thing that I think is missing from your hydraulic system is the unloading valve.  Many of the machines that I have worked on had an unloading valve to direct flow to the tank at low pressure to reduce heating when the system was in standby.

Partner Zone
More Blogs from Guest Blogs
Practically all electronic devices today contain metals that may be coming from conflict-ravaged African countries. And political pressures will increasingly influence how these minerals are sourced and used in products.
Conformal coatings present themselves as space-saving alternatives to enclosures for protecting the circuit boards of automotive electronics. They can also provide electrical insulation.
Design for manufacturing (DFM) in mold production means that mold designers evaluate the manufacturability of their molds in the early stage of mold development by collecting all relevant information and applying it to their designs. They also have to consider many other factors, including flow balance, structural stress, and assembly tolerance, in order to ensure successful molding production.
Some adhesives provide strong structural bonds but take hours to fixture and attain handling strength. The technologies that offer the fastest cure do not bear loads or withstand stresses. A new class of adhesives aims to make both stick.
The continued growth of wireless health is a near-certainty. And engineers will be the key to developing and advancing technology solutions.
Design News Webinar Series
10/1/2015 11:00 a.m. California / 2:00 p.m. New York
9/10/2015 11:00 a.m. California / 2:00 p.m. New York
8/13/2015 11:00 a.m. California / 2:00 p.m. New York
10/20/2015 8:00 a.m. California / 11:00 a.m. New York
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 5 - 9, Standards for the Internet of Things (IoT)
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Learn More   |   Login   |   Archived Classes
Twitter Feed
Design News Twitter Feed
Like Us on Facebook

Sponsored Content

Technology Marketplace

Copyright © 2015 UBM Canon, A UBM company, All rights reserved. Privacy Policy | Terms of Service