Let's face it: things break. In every manufacturing company, chances are good that at some time or another, you'll find a group of engineers and technicians standing around a broken part, scratching their heads, and asking, "Why?"
Sometimes parts break during testing under extreme conditions. These failures help us to understand the limits of a design. Other times, parts fail unexpectedly in service. These are the failures we would all like to avoid. At best, they lead to unhappy customers. At worst, they can lead to people being hurt or even killed. The good news is that a solid understanding of potential failure modes can help us prevent service failures.
The simplest failure mode to understand is overload. This is what happens when the load on a part exceeds the material's strength. Exceeding the yield strength will cause the part to permanently deform. Exceeding the ultimate strength will cause it to break. In either case, the failure occurs immediately.
Assuming you've done your stress analysis right, parts shouldn't fail in overload under normal operating conditions. So an overload failure means one of two things: either the load was too high, or the material's strength was too low.
As an example of the latter, the cam lever of a mechanical brake bent permanently the first time the brake was applied. The bend reduced the lever's stroke, preventing the brake from fully actuating. Fortunately, all of the brakes were tested prior to being shipped to the customer; otherwise, this could have been a dangerous situation. (This was an emergency brake for heavy equipment.) It turned out that the lever supplier had substituted hot-rolled, low-carbon steel for the cold-rolled, medium-carbon steel which had been specified. The steel the supplier used had a much lower yield strength than the specified steel. All of the levers had to be replaced, at the supplier's expense. The attempt to substitute a cheaper material turned out to be quite costly for the supplier.
Substitution of one material for another is not the only reason why a material's strength might be low. For example, improper heat treatment -- usually too high a temperature, too long of a time, or too slow of a cooling rate -- can lead to low strength. (For carburizing or nitriding heat treatments, too low of a temperature or too short of a time can also lead to low strength.) But even if a part is made from the correct material and receives the correct heat treatment, things can happen in service, which may reduce its strength. For example, exposure to high temperatures will generally decrease the strength of metal parts. For plastic parts, add ultraviolet light and exposure to certain chemicals to the list of things that can reduce strength.
If a part breaks in overload, and the material's strength is not too low (which can often be determined by a simple hardness test), then the load must have been too high. In many cases, examination of the failed part can provide clues as to which direction the load came from, and what type of load -- tension, compression, torsion, or bending -- it was. The question then becomes: Where did the load come from? Answering this question requires careful consideration of the mechanical system as a whole. Often, the broken part may turn out to have been an innocent bystander. For example, misalignment of another part might have produced abnormally high loads.
Avoiding overload failures, then, is a matter of understanding the forces that act on a part and the properties of the material from which it is made. It's also important to understand variables, which may cause either the loads or the material properties to differ from their normal values. As we'll see, these principles are also the key to understanding other failure modes. In my next post, I'll discuss how to apply these principles to fatigue failures.
Dave Palmer certainly got it right in the comments about nonlinear stress analysis. And I would point out that vibration is often an unanticipated mechanism for the excess stress that starts those cracks. In addition, the vibration often leads to the fatigue failure that starts the process. Of course, the amplitude of the vibration is much greater in cases where there is resonance. So now there is a whole list of things to beware of.
Hey @Dave Palmer, thanks for an awesome post! It's been a while since I've left my industry position, but all of the terms came flooding back. My development team was tasked with creating measurement techniques to complement / verify the FEA. We developed Temperature-sensitive Paint to measure and track propagating fatigue cracks while the part was under test. We developed Pressure-sensitive paint to measure aerodynamics and surface stress distributions. One of the most interesting projects was developing Strain-sensitive Paint for Ford Visteon to visualize whole-body strain-distribution on truck axles (now commercially known as Strain-Sensitive Skin, S3). All of that development was done in the late 1990's. I'm not sure how popular the techniques are now...
@Chuck: Usually, in mechanical engineering, the term "working stress" simply means the stress which a component experiences under working loads. Typically, engineers and designers try to keep the working stress below the yield strength, divided by an appropriate factor of safety. (The yield strength divided by the factor of safety is sometimes called the "allowable stress" or the "design stress").
Thanks, Dave. I brought the topic of yield strength because I seem to remember something from my distant past called, "working stress" design. I believe working stress was not based on yield strength, but I'm really not sure.
@bentarrow: I assume you're using a linear FEA package. Nonlinear FEA would give you a much more accurate picture of localized yielding and load redistribution. Otherwise, you may just want to point out to your customers that the high stresses at the transition are a result of the assumptions of the FEA model. This may or may not be a satisfying answer to them, but it's true.
If you can do actual physical testing, this might also help to convince them. You could look into using a product like Stresscoat to measure the actual tensile strains, and compare this to the results of your FEA model. If the actual part is too big to test in the lab, you might be able to use a scale model; FEA can help you understand how to appropriately scale the loads so that you get the correct stresses.
@TJ McDermott: The all-important question is, "Where is the load coming from?" As you point out, responding to failures by simply beefing up whichever part happens to break often just results in other parts breaking. At the end of the day, it results in assemblies which are extremely robust, but which are also unnecessarily heavy and expensive.
There's no substitute for a solid engineering analysis of the mechanical system as a whole. If you understand where the load is coming from, you can address the source of the problem, rather than constantly beefing up parts to compensate.
As I said before, the part which breaks is often an innocent bystander. Don't blame the part for the inadequacies of the design!
The subject of "getting the red out" is my current challenge as my design department is just now using FEA. I have had other FEA users at other company locations run FEA on parts in the past & early-on found this issue on linear static analysis of steel forgings. The loading is static and the cross sections are "L shaped" so that there is a bending stress at the inside transion from vertical to horizontal. I've found no amount of thickening the cross section ever completely eliminates the red (below yield). I have seen a report from a P.E. on a similar part where the P.E. concluded that "slight yielding in this area relieves the high stress concentration and then distributes the load more evenly accross the cross section of the part" - or words to that effect.
That's all well & good but my issue is how to justify the "remaining red" in a report that will be reviewed by other engineers who are not M.E.'s (Petroleum Engineers) - and who are the customer in this case. Any brief suggestions and or recommended literature on this subject would be most welcome.
It's interesting to watch what happens when a part is redesigned, "beefed up" because it's been breaking in the field. If the redesign works correctly, the part is no longer the "weakest link", and something else now is.
The usual progression is a series of parts end up being redesigned, one at a time, as each becomes the weakest link in turn.
My experience has been that operators have the unique ability to find every unintented use of a piece of machinery - causing real eningeering challanges when it comes time to find out what REALLY went wrong.
On April 21, NASA launched a novel project, putting into orbit three satellites that employ an off-the-shelf commercial smartphone as the control system.
The legacy endpoint devices that control our critical infrastructure (utility systems, water treatment plants, military networks, industrial control systems, etc.) are some of the most vulnerable devices on the Internet.
In a switched-capacitor filter, capacitors and switches take the place of resistors and accurately reproduce the characteristics of continuous-time Bessel, Butterworth, and elliptical filters.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 5
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
For industrial control applications, or even a simple assembly line, that machine can go almost 24/7 without a break. But what happens when the task is a little more complex? That’s where the “smart” machine would come in. The smart machine is one that has some simple (or complex in some cases) processing capability to be able to adapt to changing conditions. Such machines are suited for a host of applications, including automotive, aerospace, defense, medical, computers and electronics, telecommunications, consumer goods, and so on. This radio show will show what’s possible with smart machines, and what tradeoffs need to be made to implement such a solution.
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
10 
