Many years ago I build a power lock, but with a different, and simpler, approach. The power switching component was activated from the output of a window comparator. The comparator was fed from a voltage divider, and one of the resistors for the dividing chain was in a 3.5mm audio jack which had to be inserted in a socket for the correct voltage to be set and the power turned on. Nothing more than a transformer/bridge/cap supply, dual op-amp, and relay. basically.
Having kids around the shop can be stressful at best.
I had solved this power problem years ago with store bought devices.
It was more expensive but did not require a lot of mods to the wiring(eg: dual gang box not needed).
I used the X-10 system for the outlets and lighting and just popped off the control keypad from the control switch as I left the shop. I'm a little hesitant to install non-UL/CSA approved parts to my wirng for insurance reasons. Nice job on the solution but can't bring myself to put my house at risk. I learned the hard way, once burned...
I agree entirely with keeping kids safe by securing inherently dangerous items around the house and garage. I've done the same the entire time of having kids in the house, starting with "baby proofing" the house when my children were first born. I've always been sort of a safety fan or buff since being in the Boy Scouts. Safety is something done before an accident...hence the saying "safety is no accident"!
Although it seems like a cool solution to make a home-made switch system for the power outlets in the garage or workshop, I'm not so sure it would meet "code" requirements. If the device is not UL tested and listed, it's probably not legal to use connected to the house power. I think commercially available power locking devices would be better. I have six quad outlets in my garage, so I never have to look for a vacant electrical outlet.
My safety system was to lock-up ALL tools, especially all power tools. I always considered my electric chainsaw to be extremely dangerous, as well as circular saw, saber saw, power drill, etc. Of course, all guns are secured even better than the power tools and hand tools. Also, we always secured our car keys to prevent kids from getting any silly ideas (I've heard many stories of 12 year olds taking the parents car for a drive). As a result, my three daughters (all young adults now), all grew-up in a relatively safe and secure house with no serious injuries...and no kid's friends hurt either.
William, what would be the total cost factor and any precautions to avoid electric shock and to prevent current leakages. If by chance forget the secret code, any resetting mechanisms either for regenerate a new one or recover the secret code.
I think the design is pretty solid. While not an expert I think it is needing a surge/lightning protector, confirmed/qualified materials/parts and $ before it could be considered for certifcation and only if hter was a real market. The relay provides the isolation, leaving the buttons, as the user interface. The 10 ohm carbon resistor, the inductor both add a bit of fusing. The regulator has thermal protection.
As for the code recovery and programming...The controller can be (re)coded to provide either. Probably something like setting a recovery mode by depressing both buttons and the coded combination being sequenced to the LEDs. This was NOT considered for this submittal. Controllers are 'lovely' parts..the possibilities go on and on.
I appreciate that there are lots of solutions to this function. Some are more or less fun and interesting. For gadget freaks there is also the 'cool' factor to be considered.
From Dell / Intel® New Paradigms in Design Work Scott Hamilton, vertical market strategist for Dell Precision workstations, 5/2/2013 3
Early in my career, I worked as a draftsman and remember the days of drawing on vellum with numbered pencils and Mylar with plastic lead. This was a fun experience in the sense that I ...
I've been using workstations for more than 10 years and love finding ways to get more performance from my system. With demanding professional applications that require more power each ...
A lasting memory from my first job as an engineer in an auto assembly plant is standing on hard concrete at six in the morning, vending-machine coffee clutched in hand, listening to ...
A quick look into the merger of two powerhouse 3D printing OEMs and the new leader in rapid prototyping solutions, Stratasys. The industrial revolution is now led by 3D printing and engineers are given the opportunity to fully maximize their design capabilities, reduce their time-to-market and functionally test prototypes cheaper, faster and easier. Bruce Bradshaw, Director of Marketing in North America, will explore the large product offering and variety of materials that will help CAD designers articulate their product design with actual, physical prototypes. This broadcast will dive deep into technical information including application specific stories from real world customers and their experiences with 3D printing. 3D Printing is
To save this item to your list of favorite Design News content so you can find it later in your Profile page, click the "Save It" button next to the item.
If you found this interesting or useful, please use the links to the services below to share it with other readers. You will need a free account with each service to share an item via that service.
Tweet This
18 
