HOME  |  NEWS  |  BLOGS  |  MESSAGES  |  FEATURES  |  VIDEOS  |  WEBINARS  |  INDUSTRIES  |  FOCUS ON FUNDAMENTALS
Blogs

NO RATINGS
Page 1/3  >  >>
User Rank
Blogger
Household solution
4/17/2013 11:29:10 AM
NO RATINGS
I always enjoy the Gadget Freaks that solve household problems. This is an elegant example of a bit of ingenuity making life easier in the home.

User Rank
Blogger
Re: Household solution
4/17/2013 6:22:12 PM
NO RATINGS
As I've always said, Rob, we've got smart readers. Also frugal. The most expensive part of this solution is the solid state relay at \$21.

User Rank
Gold
garage lights
4/18/2013 9:58:36 AM
NO RATINGS
I had a similar problem where some of the garage lights were going to be blocked by the opened door.  I solved it by placing the ligths so that they were aove the horizontal windows in the door when it was in the open position - much of the light made it to the room down below in that position.

User Rank
Blogger
Re: Household solution
4/18/2013 10:22:04 AM
NO RATINGS
I enjoy these as well, Rob, especially since I would never imagine doing anything iike they do to fix something. Lucky I know some Gadget Freaks of my own who I call in when I need something done!

User Rank
Iron
4/18/2013 11:13:29 AM
NO RATINGS
I assume the SSR is triac or SCR based.  Most are zero voltage switching and require holding current.  What kind of flourscent lights did you have?  If they had electronic ballast without power factor correction did the circuit work?  Magnetic ballast may not have sufficient holding current.

User Rank
Platinum
Re: Household solution
4/20/2013 4:59:18 PM
NO RATINGS
Rob, The key word here is "elegant. Sometimes the best solutions to a challenging problem are simple ones. Very nice Gadget Freak article!

User Rank
Platinum
WHY?
4/22/2013 3:39:35 PM
NO RATINGS

#1)  Is there any reason why you didn't connect the transformer primary AFTER the switch?  Why have the power on to the transformer IF the lights in the garage are NOT being used?

#2)  Why switch the low side of the AC circuit instead of the high side?  Was it a matter of wiring convenience?

#3)  Since your circuit is directly connected to house wiring, in case of a fire, could the fire marshall disallow an insurance claim because NON-UL-approved wiring devices are being used?

Thank you.

User Rank
Blogger
Re: Household solution
4/22/2013 7:52:13 PM
NO RATINGS
I agree, MrDon. Creating a simple solution may take more creativity than building a complex solution.

User Rank
Iron
Re: WHY?
4/23/2013 4:19:39 PM
NO RATINGS
I considered switching the transformer but thought that cycling power to it might be harder on it than leaving it on. I ended up thinking of it as another door bell transformer (it is), which stays on all the time.

I used the relay and switched low voltage (16 V) to prevent exposure to line voltage out on the garage door track.

I don't know about the insurance issue. I designed it to be as safe as possible with line voltage contain in the junction box. The low voltage circuit is like a door bell circuit.

Thank you for writing.

Regards,

Tom

User Rank
Platinum
Re: WHY?
4/24/2013 7:57:58 AM
NO RATINGS

#1)  I guess in the overall scheme of things, the few watts per day that the bell transformer uses are not going to bring down your local power grid.  Since those transformers are fairly high impedance, it probably doesn't matter one way or another.  IF it was my circuit design, I would probably have put it on the swiched side of the AC circuit, just because that's the way my brain is "wired".

#2)  What I was referring to was placing the SSR on the low side of the AC circuit, not the control relay.  Whenever I've used SSR's in control applications, I've always fed them, and taken the loads from them.

#3)  I'm NO attorney either, but in today's litigious atmosphere, where INsurance companies generally contrive to void policyholders' claims, seeing this circuit made me take pause.  YOu can bet your bottom dollar that some over-zealous investigator COULD insert a sentence or more about your circuit in an attempt to deny a claim.  Although I've never wired anything of my own design into the electro-mechanics of our houses (and I've thought of many applications over the decades!), I just question the efficacy of doing so now.  In my younger years I've totally wired several houses from the "pole" to the last outlet, so I did have intimate knowledge of acceptable wiring practices.

Page 1/3  >  >>
 Partner Zone
This collection of practical Gadget Freak projects includes a walking stick for the blind as well as an indicator that calls for help for stroke victims.
Your cat demands to be fed on time. With some technical know-how and a 3D printer you can build your own automated cat food dispenser.
Design News has a long Gadget Freak history and today we revisit some of the more memorable projects that actually help solve problems.
Halloween will be here before you know it. And the zombie apocalypse may come even sooner. Best to prepare yourself by building your own security system to safeguard against the walking dead.
Need some security in your DIY workshop? Gadget Freak Ben Pawlowski and his team show you how to build a security camera/alarm modeled after the turret guns from the popular video game, Portal.
Quick Poll
The Continuing Education Center offers engineers an entirely new way to get the education they need to formulate next-generation solutions.
Oct 10 - 14, Embedded System Design Techniques™: Getting Started Developing Professional Embedded Software
SEMESTERS: 1  |  2  |  3  |  4  |  5  |  6 |  7 | 8 | 9 | 10

Focus on Fundamentals consists of 45-minute on-line classes that cover a host of technologies. You learn without leaving the comfort of your desk. All classes are taught by subject-matter experts and all are archived. So if you can't attend live, attend at your convenience.
Next Course September 27-29: