Toulouse, France –Overall weight and
fuel efficiency are important to an aircraft's performance, so Airbus engineers
looked past the 3,000-psi systems typically used in large aircraft and designed
the first-ever commercial 5,000-psi hydraulic system for use in the A380
aircraft. The new high-pressure system provides the fluid power needed for
controlling the aircraft's flaps, rudder, and other control surfaces while
reducing the overall weight of the hefty 555-passenger aircraft by 2,500
lb.
Instead of the standard 3,000 psi
hydarulic systems found on many large commercial aircraft, the new Airbus
A380 will use a 5,000 psi hydraulic system for moving the rudders, flaps,
and other flight-control surfaces.
"Any saving in the basic weight of an aircraft is directly translated into an increase in its revenue payload capability," says Airbus A380 Program Engineer Derek Davies. The problem he and other engineers encountered when designing the A380 hydraulic system is that the equipment, if designed to operate at the traditional 3,000 psi, would be too big. "For example, the diameter of the hydraulic inlet hose line for the A380 at 5,000 psi is two inches," says John Halat, the director of research and new product development at Eaton Corporation's aerospace operations. "It would be much bigger and bulkier, up to three inches, using a conventional 3,000 psi system," says Halat. Bigger hoses require bigger fittings and mounting brackets, which also add weight and bulk.
Typical applications of hydraulic power
on commercial and military aircraft include rudders, wing flaps, engines,
and landing gear.
Halat explains that the weight reduction on the A380 is a direct result of how the hydraulic power is converted into motion by the electrohydraulic actuators that control rudders, ailerons, flaps, and other flight surfaces. "Consider, for example, a single actuator controlling the rudder movement," explains Halat. "This actuator needs a specified amount of mechanical power for moving the flight control surface at a given rate and against a given force." The A380 has upper and lower rudders that are sized for a stall load of 22.5 tons each. The mechanical power required by the actuator is the product of the force needed to move the surface times the velocity of the flying control surface.
The hydraulic system provides the equivalent amount of power to the actuator in the form of fluid power. The hydraulic pump, which is usually mounted on the engine gearbox, extracts mechanical power from the engine and converts it to hydraulic power for use in the system.
As the pump supplies hydraulic flow to the system, the pressure developed is the resistance to the flow in the system. The hydraulic power available in the system is the product of the pressure times the flow rate. This power flows through the fluid tubing and hoses to the actuator. The available fluid power equals the pressure times the flow. With a fixed power requirement, these two variables vary inversely with each other. So, if the pressure goes up, the flow rate comes down.
For the A380, Eaton supplies Airbus with
the hydraulic hose, fittings, and engine-driven hydraulic pumps like the
one shown here.
"Designing the system to operate at 5,000 psi allows a 40% reduction in the flow rate compared to a 3,000-psi system built to the scale needed for the A380," says Halat. The jumbo jet contains a large number of actuators, many to drive its large number of control surfaces. The pump and fluid delivery system must meet the maximum flow rate of multiple actuators functioning at one time. In a 3,000-psi system for the A380, the flow rate would require a 70-gpm pump. However, the 5,000-psi system reduces the necessary flow to only 42 gpm. Airbus achieved a 20% weight reduction by going to the higher pressure and using a smaller size displacement pump with lower flow rate.
The overall system component weight reduction attributed to the 5,000-psi hydraulic system is approximately 2,500 lb. While the volume of power generation and motion control components is also smaller, the majority of the volume and weight saving occurs in the 250 to 500 fittings and the hydraulic lines which, in some cases, run the length of the aircraft.
Trade-offs resulting from the move to 5,000-psi hydraulics include materials used for the sealing of cylinder blocks, pistons, and other pump components. Elastomeric sealing is now required in places that normally allow metal-to-metal sealing.
Eaton has a track record in 5,000-psi hydraulic applications. The military currently uses the company's 5,000-psi hydraulic pumps, fittings, and hose in the F-18, V-22, and other aircraft.
For more information
Go to www.designnews.com and click on Request Product Info in the navigation bar, or enter the number on the Reader Service Card:
Hydraulic systems from Eaton, www.eaton.com: Enter 552
JUNE 26TH WEBCAST: Collaborative Requirements Engineering
Speed your innovation. Capture the "voice of the customer" and translate customer requests into user requirements that define new products. Find out why the new ENOVIA Requirements Management solution enables organizations to improve their overall global requirements management process. Read More
Mechatronics in action
Successful synergistic integration of controls, electronics, computers and mechanical systems is key to the 21st century design process. Unlock the secrets at the Mechatronics Zone!
Webcast: Sensor Know-How Now
Join our moderator Randy Frank and John Keating from Cognex and explore Solving Industrial Inspection Problems. Read More
Engineering Concept Conduit
Engineering Concept Conduit looks at new products and the components that make them exceptional. Each month we’ll look at a new electronic product and see what makes it tick from an engineering point of view. We’ll explore the design and engineering challenges for the product and examine the components that solved those challenges.
Light Matters: Systems Level Approach to HBLED illumination applications
Its good practice to apply a systems-level approach to high-brightness LED (HBLED) illumination applications. Minimally, the system includes the optical, thermal and electrical characteristics of the of the HBLED, the lens (if any) which is built-in to its package, secondary optics such as external plastic lenses/reflectors to direct the light as your application requires and power driver electronics. Read More
Design News RSS News Feeds
Webcast: Sensor Know-How Now
